PITTING RESISTANCE
PREN calculator and PREN number table
Enter chromium, molybdenum, tungsten and nitrogen to calculate PREN, or search for a grade to see its PREN range from the composition limits. PREN is used to compare stainless steels and nickel alloys by their resistance to pitting corrosion.
Chemical composition
Enter weight per cent; you can use the heat analysis from the mill certificate. Leave W = 0 for grades without tungsten.
PREN = Cr + 3.3 (Mo + 0.5 W) + 16 N
PREN value
Comparison
PREN number table
PREN of stainless steels, duplex grades and nickel alloys, calculated from the composition limits on each grade page (Cr, Mo, W and N in weight %).
Stainless steelsMaterial no. · PREN · Cr · Mo · N · W
| Grade | Material no. | PREN | Cr | Mo | N | W |
|---|---|---|---|---|---|---|
| X2CrNi12 | 1.4003 | 10.5–13.0 | 10.5–12.5 | – | 0–0.03 | – |
| Custom 455 | 1.4543 | 11.0–14.2 | 11–12.5 | 0–0.5 | – | – |
| 410 | 1.4006 | 11.5–13.5 | 11.5–13.5 | – | – | – |
| 410S | 1.4000 | 12.0–14.0 | 12–14 | – | – | – |
| 420 | 1.4021 | 12.0–14.0 | 12–14 | – | – | – |
| 420 | 1.4028 | 12.0–14.0 | 12–14 | – | – | – |
| 420F | 1.4029 | 12.0–15.5 | 12–13.5 | 0–0.6 | – | – |
| 416 | 1.4005 | 12.0–16.0 | 12–14 | 0–0.6 | – | – |
| 420 | 1.4034 | 12.5–14.5 | 12.5–14.5 | – | – | – |
| Custom 465 | 1.4614 | 13.5–16.6 | 11–12.5 | 0.75–1.25 | – | – |
| 1.4923 | 1.4923 | 13.6–16.5 | 11–12.5 | 0.8–1.2 | – | – |
| 15-5 PH | 1.4545 | 14.0–17.2 | 14–15.5 | 0–0.5 | – | – |
| 431 | 1.4057 | 15.0–17.0 | 15–17 | – | – | – |
| 17-4 PH | 1.4542 | 15.0–19.2 | 15–17.5 | 0–0.5 | – | – |
| X50CrMoV15 | 1.4116 | 15.7–18.1 | 14–15.5 | 0.5–0.8 | – | – |
| 430 | 1.4016 | 16.0–18.0 | 16–18 | – | – | – |
| 430Nb | 1.4511 | 16.0–18.0 | 16–18 | – | – | – |
| 17-7 PH | 1.4568 | 16.0–18.0 | 16–18 | – | – | – |
| 301 | 1.4310 | 16.0–23.2 | 16–19 | 0–0.8 | 0–0.1 | – |
| 1.4104 | 1.4104 | 16.2–19.5 | 15.5–17.5 | 0.2–0.6 | – | – |
| 1.4938 | 1.4938 | 16.3–19.7 | 11–12.5 | 1.5–2 | 0.02–0.04 | – |
| Super 13Cr | 1.4415 | 16.5–21.8 | 11.5–13.5 | 1.5–2.5 | – | – |
| 430F | 1.4105 | 16.7–20.0 | 16–18 | 0.2–0.6 | – | – |
| A-286 | 1.4980 | 16.8–21.0 | 13.5–16 | 1–1.5 | – | – |
| 1.4594 | 1.4594 | 17.0–21.6 | 13–15 | 1.2–2 | – | – |
| 321 | 1.4541 | 17.0–19.0 | 17–19 | – | – | – |
| 347 | 1.4550 | 17.0–19.0 | 17–19 | – | – | – |
| 1.4742 | 1.4742 | 17.0–19.0 | 17–19 | – | – | – |
| 305 | 1.4303 | 17.0–20.6 | 17–19 | – | 0–0.1 | – |
| 303 | 1.4305 | 17.0–20.6 | 17–19 | – | 0–0.1 | – |
| 304Cu | 1.4567 | 17.0–20.6 | 17–19 | – | 0–0.1 | – |
| 303Cu | 1.4570 | 17.0–22.6 | 17–19 | 0–0.6 | 0–0.1 | – |
| Nitronic 60 | – | 17.3–20.9 | 16–18 | – | 0.08–0.18 | – |
| 440C | 1.4125 | 17.3–20.6 | 16–18 | 0.4–0.8 | – | – |
| 441 | 1.4509 | 17.5–18.5 | 17.5–18.5 | – | – | – |
| 304 | 1.4301 | 17.5–21.1 | 17.5–19.5 | – | 0–0.1 | – |
| 304L | 1.4307 | 17.5–21.1 | 17.5–19.5 | – | 0–0.1 | – |
| 1.4530 | 1.4530 | 17.6–19.8 | 11.5–12.5 | 1.85–2.15 | 0–0.01 | – |
| 1.4596 | 1.4596 | 17.6–19.9 | 11.5–12.5 | 1.85–2.15 | 0–0.02 | – |
| 1.4122 | 1.4122 | 18.1–21.8 | 15.5–17.5 | 0.8–1.3 | – | – |
| 13-8 Mo PH | 1.4534 | 18.9–21.7 | 12.25–13.25 | 2–2.5 | 0–0.01 | – |
| 1.4123 | 1.4123 | 18.9–29.1 | 14–16 | 1–2.5 | 0.1–0.3 | – |
| 434 | 1.4113 | 19.0–22.6 | 16–18 | 0.9–1.4 | – | – |
| X15CrNiSi20-12 | 1.4828 | 19.0–22.8 | 19–21 | – | 0–0.11 | – |
| 301LN | 1.4318 | 19.3 | 17.5 | – | 0.11 | – |
| 1.4818 | 1.4818 | 19.9–23.2 | 18–20 | – | 0.12–0.2 | – |
| 1.4112 | 1.4112 | 20.0–23.3 | 17–19 | 0.9–1.3 | – | – |
| 15-7 Mo | – | 20.6–25.9 | 14–16 | 2–3 | – | – |
| 1.4835 | 1.4835 | 21.9–25.2 | 20–22 | – | 0.12–0.2 | – |
| 309S | 1.4833 | 22.0–25.8 | 22–24 | – | 0–0.11 | – |
| 1.4114 | 1.4114 | 22.5–27.8 | 17.5–19.5 | 1.5–2.5 | – | – |
| 1.4762 | 1.4762 | 23.0–26.0 | 23–26 | – | – | – |
| 446 / X8Cr24 | 1.4763 | 23.0–27.6 | 23–26 | – | 0–0.1 | – |
| 316Ti | 1.4571 | 23.1–26.8 | 16.5–18.5 | 2–2.5 | – | – |
| 1.4578 | 1.4578 | 23.1–27.4 | 16.5–17.5 | 2–2.5 | 0–0.1 | – |
| 316 | 1.4401 | 23.1–28.4 | 16.5–18.5 | 2–2.5 | 0–0.1 | – |
| 1.4598 | 1.4598 | 23.1–28.4 | 16.5–18.5 | 2–2.5 | 0–0.1 | – |
| 316L | 1.4404 | 23.1–30.0 | 16.5–18.5 | 2–3 | 0–0.1 | – |
| 314 | 1.4841 | 24.0–27.8 | 24–26 | – | 0–0.11 | – |
| 310S | 1.4845 | 24.0–27.8 | 24–26 | – | 0–0.11 | – |
| AM 355 | – | 24.4–28.8 | 15–16 | 2.5–3.25 | 0.07–0.13 | – |
| 444 | 1.4521 | 24.6 | 18 | 2 | – | – |
| 316L / 316LMo | 1.4435 | 25.3–30.5 | 17–19 | 2.5–3 | 0–0.1 | – |
| 316LN | 1.4429 | 26.7–31.9 | 16.5–18.5 | 2.5–3 | 0.12–0.22 | – |
| 316LVM | 1.4441 | 26.7–28.3 | 17.5 | 2.8 | 0–0.1 | – |
| 317L | 1.4438 | 27.4–34.3 | 17.5–19.5 | 3–4 | 0–0.1 | – |
| 446 | 1.4749 | 28.4–33.0 | 26–29 | – | 0.15–0.25 | – |
| Nitronic 50 | – | 28.7–39.8 | 20.5–23.5 | 1.5–3 | 0.2–0.4 | – |
| S31675 | 1.4472 | 30.1–39.9 | 19.5–22 | 2–3 | 0.25–0.5 | – |
| 317LMN | 1.4439 | 31.6–38.5 | 16.5–18.5 | 4–5 | 0.12–0.22 | – |
| 310MoLN | 1.4466 | 32.2–36.8 | 24–26 | 2–2.5 | 0.1–0.16 | – |
| 904L | 1.4539 | 32.2–39.9 | 19–21 | 4–5 | 0–0.15 | – |
| 1.4565 | 1.4565 | 42.0–52.1 | 24–26 | 4–5 | 0.3–0.6 | – |
| Alloy 926 | 1.4529 | 42.2–48.1 | 20–21 | 6–7 | 0.15–0.25 | – |
| 254 SMO | 1.4547 | 43.3 | 20 | 6.1 | 0.2 | – |
| 1.4659 | 1.4659 | 49.2–58.6 | 23–25 | 5.5–6.5 | 0.35–0.5 | 1.5–2.5 |
| 1.4652 | 1.4652 | 53.3–60.2 | 23–25 | 7–8 | 0.45–0.55 | – |
Duplex stainless steelsMaterial no. · PREN · Cr · Mo · N · W
| Grade | Material no. | PREN | Cr | Mo | N | W |
|---|---|---|---|---|---|---|
| 2304 | 1.4362 | 23.1–29.7 | 22–24.5 | 0.1–0.6 | 0.05–0.2 | – |
| Lean duplex 2202 | 1.4062 | 24.1–30.0 | 21.5–24 | 0–0.45 | 0.16–0.28 | – |
| 2101 | 1.4162 | 24.5–28.6 | 21–22 | 0.1–0.8 | 0.2–0.25 | – |
| 2404 | 1.4662 | 29.5–36.4 | 23–25 | 1–2 | 0.2–0.3 | – |
| 329 | 1.4460 | 30.1–37.8 | 25–28 | 1.3–2 | 0.05–0.2 | – |
| Duplex 2205 | 1.4462 | 30.9–38.1 | 21–23 | 2.5–3.5 | 0.1–0.22 | – |
| 255 | 1.4507 | 37.1–44.0 | 24–26 | 3–4 | 0.2–0.3 | – |
| Super duplex 2507 | 1.4410 | 37.7–46.5 | 24–26 | 3–4.5 | 0.24–0.35 | – |
| Super duplex S32760 | 1.4501 | 37.9–45.7 | 24–26 | 3–4 | 0.2–0.3 | 0.5–1 |
Nickel and cobalt alloysMaterial no. · PREN · Cr · Mo · N · W
| Grade | Material no. | PREN | Cr | Mo | N | W |
|---|---|---|---|---|---|---|
| NiCr 60/15 | 2.4867 | 15.0 | 15 | – | – | – |
| Alloy 330 | 1.4864 | 15.0–17.0 | 15–17 | – | – | – |
| Alloy X-750 | 2.4669 | 15.5 | 15.5 | – | – | – |
| Alloy 751 | 2.4694 | 16.0 | 16 | – | – | – |
| Alloy 600 | 2.4816 | 16.0 | 16 | – | – | – |
| Alloy DS | 1.4862 | 17.5 | 17.5 | – | – | – |
| Nimonic 90 | 2.4632 / 2.4969 | 18.0–21.0 | 18–21 | – | – | – |
| Alloy 800 | 1.4876 | 19.0–23.0 | 19–23 | – | – | – |
| Incoloy 800H | 1.4958 | 19.0–23.0 | 19–23 | – | – | – |
| Incoloy 800HT | 1.4959 | 19.0–23.0 | 19–23 | – | – | – |
| NiCr 80/20 | 2.4869 | 20.0 | 20 | – | – | – |
| Nimonic 75 | 2.4951 | 20.0 | 20 | – | – | – |
| Nimonic 80A | 2.4952 | 20.0 | 20 | – | – | – |
| Alloy 601 | 2.4851 | 23.0 | 23 | – | – | – |
| Alloy 20 | 2.4660 | 25.6–30.9 | 19–21 | 2–3 | – | – |
| Alloy 901 | 2.4662 | 27.5–37.1 | 11–14 | 5–7 | – | – |
| Alloy HR-160 | 2.4880 | 28.0–33.0 | 28 | 0–1 | – | 0–1 |
| Alloy HR-120 | 2.4854 | 28.2–32.3 | 25 | 0–1 | 0.2 | 0–0.5 |
| Alloy 718 | 2.4668 | 28.9 | 19 | 3 | – | – |
| Alloy 925 | – | 29.9 | 20 | 3 | – | – |
| Incoloy 825 | 2.4858 | 32.9 | 23 | 3 | – | – |
| Waspaloy | 2.4654 | 33.2 | 19 | 4.3 | – | – |
| Elgiloy | 2.4711 | 38.8–47.4 | 19–21 | 6–8 | – | – |
| Nimonic 263 | 2.4650 | 39.1 | 20 | 5.8 | – | – |
| Alloy 333 | 2.4608 | 39.9 | 25 | 3 | – | 3 |
| L-605 | 2.4964 | 44.8 | 20 | – | – | 15 |
| Alloy 230 | 2.4733 | 44.8–58.7 | 20–24 | 1–3 | – | 13–15 |
| MP35N | – | 48.7–55.7 | 19–21 | 9–10.5 | – | – |
| Alloy 625 | 2.4856 | 51.2 | 21.5 | 9 | – | – |
| Alloy 617 | 2.4663 | 51.7 | 22 | 9 | – | – |
| Alloy G-30 | 2.4603 | 52.3 | 30 | 5.5 | – | 2.5 |
| Alloy X | 2.4665 | 52.7 | 22 | 9 | – | 0.6 |
| Hastelloy C-22 | 2.4602 | 70.5 | 21 | 13.5 | – | 3 |
| Alloy 686 | 2.4606 | 73.4–86.4 | 19–23 | 15–17 | – | 3–4.4 |
| Alloy C-2000 | 2.4675 | 75.8 | 23 | 16 | – | – |
| Hastelloy C-276 | 2.4819 | 76.2 | 16 | 16.5 | – | 3.5 |
| Alloy B-2 | 2.4617 | 89.8 | 0.7 | 27 | – | – |
What is PREN?
PREN (pitting resistance equivalent number) estimates the resistance of stainless steels and nickel alloys to pitting corrosion from their chemical composition. The formula comes from regression analysis of pitting and crevice corrosion tests in chloride solutions. A higher PREN goes with a higher critical pitting temperature (CPT).
PREN formula
The most common formula is PREN = %Cr + 3.3 × %Mo + 16 × %N. For grades containing tungsten, PREN = %Cr + 3.3 × (%Mo + 0.5 × %W) + 16 × %N is used, the form also used in ISO 15156 / NACE MR0175. With tungsten at 0 both give the same result, so the calculator uses the single formula.
The coefficients have no physical meaning; multiplying nitrogen by 16 does not make it 16 times as effective as chromium. Chromium, molybdenum and nitrogen are only partly interchangeable: each must be present at a minimum level.
How the PREN ranges in the table are calculated
Each grade’s PREN range is calculated from the composition limits on its grade page. The lower value uses the lower limits and the upper value the upper limits; an element with only a maximum (e.g. N ≤ 0.10 in 304L) counts as 0 in the lower value. Grades with a typical composition show a single value. For a specific heat, enter the actual analysis from the mill certificate into the calculator.
What PREN does not tell you
PREN is for ranking grades on one scale; on its own it does not predict how a material will behave in a given service. Temperature, chloride concentration, pH, crevice geometry, welding and the structure after heat treatment also affect resistance. Material selection should combine the relevant standard, test results and producer data.
What is pitting corrosion?
Pitting corrosion forms small but deep pits where the passive oxide film on stainless steel breaks down locally, typically under chloride ions. Most of the surface can look intact while pits grow through the wall. Seawater, saline environments and chloride-bearing process fluids are the main risks; molybdenum and nitrogen strengthen the film.
Frequently asked questions
How is PREN calculated?
PREN = %Cr + 3.3 × (%Mo + 0.5 × %W) + 16 × %N. For grades without tungsten W = 0 and the formula becomes %Cr + 3.3 × %Mo + 16 × %N. Values are in weight per cent.
What is the PREN of 316L?
For 1.4404 (316L), PREN is 23.1–30.0 from the EN 10088-3 composition limits. For 304 (1.4301), which has no molybdenum, it is 17.5–21.1.
What is the PREN of duplex 2205?
Duplex stainless steel 1.4462 (2205) has a PREN of 30.9–38.1 from its composition limits.
What PREN does super duplex have?
Super duplex grades are generally associated with a PREN above 40. For 1.4410 (2507) the range from the composition limits is 37.7–46.5; a heat at the lower limits can fall below 40, so specifications often state a minimum PREN separately.
What is the PREN of alloy 625?
From its typical composition, alloy 625 (2.4856) has a PREN of about 51.2. For 904L (1.4539) the range from the composition limits is 32.2–39.9.
Is a higher PREN always better?
No. PREN only compares resistance to pitting in chloride environments. Crevice corrosion, stress corrosion cracking, temperature and fabrication effects are not part of it.