GRADE COMPARISON
Material comparison and alternative grade finder
Choose two grades to see their designations, chemical composition, density and PREN side by side, with marked composition differences highlighted. Compositionally closest alternatives in the same material group are listed for the first grade.
304
Stainless Steel · 1.4301 · S30400
316
Stainless Steel · 1.4401 · S31600
| 304 | 316 | |
|---|---|---|
| Material group | Stainless Steel | Stainless Steel |
| Material no. (W.Nr) | 1.4301 | 1.4401 |
| EN name | X5CrNi18-10 | X5CrNiMo17-12-2 |
| AISI | 304 | 316 |
| UNS | S30400 | S31600 |
| JIS | SUS304 | SUS316 |
| Density | 7.9 g/cm³ | 8 g/cm³ |
| PREN | 17.5–21.1 | 23.1–28.4 |
| Chemical composition, % | ||
| C | ≤ 0.07 | ≤ 0.07 |
| Si | ≤ 1 | ≤ 1 |
| Mn | ≤ 2 | ≤ 2 |
| P | ≤ 0.045 | ≤ 0.045 |
| S | ≤ 0.03 | ≤ 0.03 |
| Cr | 17.5–19.5 | 16.5–18.5▼ |
| Ni | 8–10.5 | 10–13▲ |
| Mo | – | 2–2.5 |
| N | ≤ 0.1 | ≤ 0.1 |
Arrows mark elements where grade 2 is markedly higher (▲) or lower (▼) than grade 1. Values are the composition limits on the grade pages; mechanical properties depend on product form and heat treatment.
Alternatives to 304
The compositionally closest grades in the same material group. Choose one to compare it as grade 2.
A close composition does not make a grade a direct substitute; check mechanical properties, the product standard and the specification.
How to compare grades
When comparing two grades, start with the chemical composition: carbon affects strength and weldability, chromium and molybdenum corrosion resistance, nickel the austenitic structure and toughness, nitrogen strength and pitting resistance. The table places the composition limits from the grade pages side by side and marks the elements where grade 2 is markedly higher or lower. PREN expresses the difference in pitting resistance of stainless steels and nickel alloys as one number.
How alternatives are found
The list compares grades in the same material group by the average values of the main elements and ranks those with the smallest difference. Each alternative shows its most marked differences (e.g. “Mo +0.5”). This is compositional closeness, not equivalence: for substitution, check mechanical properties, the product standard, heat treatment condition and specification. For the names of the same grade in other standards, see the steel equivalent chart.
Frequently asked questions
What is the difference between 304 and 316?
316 (1.4401) contains 2–2,5% molybdenum, while 304 (1.4301) has none. Molybdenum raises pitting resistance in chlorides: PREN is 17.5–21.1 for 304 and 23.1–28.4 for 316.
What is the difference between 316 and 316L?
316L (1.4404) has at most 0,03% carbon, 316 (1.4401) at most 0,07%. The lower carbon reduces the risk of intergranular corrosion after welding.
What is the difference between 2205 and 2507?
As a super duplex, 2507 (1.4410) has more chromium (24–26%), molybdenum (3–4,5%) and nitrogen; 2205 (1.4462) has 21–23% Cr and 2,5–3,5% Mo. PREN is 30.9–38.1 for 2205 and 37.7–46.5 for 2507.
What is the difference between 17-4 PH and 15-5 PH?
Both are copper-bearing precipitation hardening martensitic stainless steels. 17-4 PH (1.4542) has 15–17,5% Cr and 15-5 PH (1.4545) 14–15,5%; the lower delta-ferrite structure of 15-5 PH improves transverse toughness.