PRECISION IN MATERIAL. CLARITY IN SUPPLY.

CALCULATORS

Metal and engineering calculators

Nineteen engineering tools in one place, led by weight calculation for steel, stainless and aluminium, shaft and hole tolerances and hardness conversion. They run in the browser on phone or desktop with no download, and the results rest on the standards’ own tables.

Metal weight calculator

Weight of bar, sheet, pipe, sections and rebar in steel, stainless, aluminium and other metals; kg/m, piece and total weight.

Open calculator

Tolerance calculator

Shaft and hole tolerances and fits (ISO 286), ISO 2768 general tolerances, and product tolerances for pipe, sheet and sections.

Open calculator

Hardness converter

Hardness conversion between HRC, HRB, HB and HV by material group, with estimated tensile strength.

Open calculator

Material comparison

Compare two steel or alloy grades side by side by composition, W.Nr, AISI, UNS, density and PREN, and see close alternatives.

Open calculator

Steel equivalent chart

Material number, EN, AISI, UNS and JIS equivalents; find the matching grade for stainless, carbon, alloy and tool steels.

Open calculator

PREN calculator

Pitting resistance from Cr, Mo, W and N, with a PREN number table for 316L, duplex, super duplex and nickel alloys.

Open calculator

Thermal expansion calculator

Length change with temperature for steel, stainless, aluminium and titanium; pipe expansion and a coefficient table.

Open calculator

Inch to mm converter

Fractional and decimal inches to millimetres and back; an inch to mm chart and pipe sizes in inches (DN, NPS, outside diameter).

Open calculator

Flange dimensions chart

Outside diameter, bolt circle, holes and bolts for EN 1092-1 PN10–PN40 and ASME B16.5 Class 150 and 300 flanges.

Open calculator

RPM and cutting speed calculator

Spindle speed from cutting speed and back, feed rate and machining time for turning, milling and drilling.

Open calculator

Taper calculator

Taper ratio (1:x), half and included angle and tailstock offset for taper turning; small diameter from an angle.

Open calculator

Thread chart

Metric coarse and fine pitches with tap drill sizes; UNC, UNF and BSP (G) inch thread tables.

Open calculator

Sheet metal flat length

Flat length for L and U bends, bend allowance and deduction; K-factor from a test bend and rolled cylinder blanks.

Open calculator

Bolt, nut and washer sizes

Wrench sizes M3–M36 (ISO and DIN), head and nut heights and ISO 7089 washer dimensions.

Open calculator

Surface roughness chart

Convert between Ra in µm and µin and N1–N12 grades; typical Rz and the difference between Ra and Rz.

Open calculator

Galvanic corrosion chart

The galvanic series in seawater; which of two metals in contact corrodes and how to prevent it.

Open calculator

Bolt torque chart

Tightening torque for metric bolts M4–M24 in classes 8.8, 10.9 and 12.9; Nm, kgf·m and ft·lbf.

Open calculator

Carbon equivalent calculator

CEV, CET and Pcm for steels, a weldability rating and the CEV range of alloy steels by grade.

Open calculator

Welding heat input calculator

Arc energy and heat input (kJ/mm) from voltage, current and travel speed, with EN 1011-1 thermal efficiency factors.

Open calculator

How to calculate metal weight

Metal weight is the part’s volume times the material density: weight (kg) = cross-section (mm²) × length (mm) × density (g/cm³) / 1,000,000. Carbon steel uses 7.85 g/cm³, stainless about 7.9–8.0 g/cm³ and aluminium about 2.7 g/cm³. A Ø50 mm steel bar 1 m long weighs about 15.41 kg. The weight calculator gives kg/m, piece and total weight for round, square, hex and flat bar, sheet, pipe, box sections, channels, beams and rebar, with an optional price per kg.

How to calculate tolerances

Shaft and hole tolerances follow ISO 286 from the nominal size and tolerance class: the class gives the upper and lower deviation for the size range. A Ø25 H7 hole has deviations of 0 / +21 µm and limits of 25 – 25.021 mm. The tolerance calculator covers single sizes, fits such as H7/g6, ISO 2768 general tolerances and product tolerances for pipe, sheet, bar and sections, with a full table for every class.

How hardness conversion works

Rockwell (HRC, HRB), Brinell (HB) and Vickers (HV) are different tests with no exact formula between them. Conversion uses comparison tables measured on both scales for the same material group: for carbon steel, 45 HRC is about 424 HB. The hardness converter uses separate tables for steel, stainless, nickel, aluminium, brass and copper and shows an estimated tensile strength with the result.

Other engineering calculations

For material selection: the steel equivalent chart (W.Nr, AISI, UNS, JIS), material comparison, PREN and carbon equivalent; for machining: cutting speed and rpm, taper and thread charts; for sheet and fasteners: flat length, flanges, bolt–nut–washer sizes and torque; plus thermal expansion, surface roughness, galvanic corrosion, welding heat input and inch–mm conversion. Every tool works in Turkish and English, and results can be copied or shared by link.

Frequently asked questions

How do you calculate the weight of metal?

Multiply cross-section by length and density: kg = mm² × mm × g/cm³ / 1,000,000. A Ø50 mm steel bar 1 m long ≈ 15.41 kg; a 1000 × 2000 × 2 mm stainless sheet ≈ 31.7 kg.

What is the formula for steel weight?

For round steel, kg/m = diameter² (mm) × 0.006165 (at 7.85 g/cm³). For Ø50 mm, 50² × 0.006165 ≈ 15.41 kg/m. Other sections use cross-section × 7.85 / 1000.

How do you calculate a tolerance?

Choose the nominal size and class (e.g. H7, g6); the ISO 286 table gives the upper and lower deviation for the size range, which are added to the nominal size. Ø25 H7: 25 – 25.021 mm.

How do you convert HRC to HB?

There is no exact formula; a comparison table for the material group is used. For carbon steel, 45 HRC ≈ 424 HB and 30 HRC ≈ 287 HB.

Do I need to download a program?

No. All tools run in the browser on phone, tablet or desktop without installation or sign-up. You can copy the result or share it by link; tables can be printed or saved as PDF.

How accurate are the results?

Calculations rest on the standards’ tables and formulas; each tool page states its sources and limits. Weights use nominal dimensions and typical density, so real parts vary with tolerances. Hardness conversions are approximate.