SURFACE ROUGHNESS
Surface roughness chart: Ra, Rz and N grades
Enter Ra in micrometres or microinches, or an N grade, to see the other values and a typical Rz. Because there is no exact conversion between Ra and Rz, Rz is given as an estimate only.
Roughness value
Rz cannot be calculated exactly from Ra; the value shown is the approximate Rz ≈ 4 × Ra used in tables.
ISO 1302
N7
- Ra (µm)
- 1.6
- Ra (µin)
- 63
- Nearest N grade
- N7 (Ra 1.6 µm)
- Rz (approx.)
- ≈ 6.4 µm
Surface roughness table
ISO 1302 N grades with Ra in micrometres and microinches; Rz is the approximate table value (≈ 4 × Ra).
N grade, Ra and approximate RzRa (µm) · Ra (µin) · Rz ≈ (µm)
| N grade | Ra (µm) | Ra (µin) | Rz ≈ (µm) |
|---|---|---|---|
| N1 | 0.025 | 1 | 0.1 |
| N2 | 0.05 | 2 | 0.2 |
| N3 | 0.1 | 4 | 0.4 |
| N4 | 0.2 | 8 | 0.8 |
| N5 | 0.4 | 16 | 1.6 |
| N6 | 0.8 | 31 | 3.2 |
| N7 | 1.6 | 63 | 6.4 |
| N8 | 3.2 | 126 | 12.8 |
| N9 | 6.3 | 248 | 25.2 |
| N10 | 12.5 | 492 | 50 |
| N11 | 25 | 984 | 100 |
| N12 | 50 | 1,968 | 200 |
What are Ra and Rz?
Ra (arithmetic mean roughness) is the average deviation of the surface profile from the mean line and the most widely used roughness value. Rz (mean roughness depth) is the average, over five sampling lengths, of the height between the highest peak and the deepest valley. Ra describes the average, Rz the peaks and valleys; a single deep scratch raises Rz noticeably while hardly changing Ra.
Can Ra be converted to Rz?
There is no exact conversion; the two values measure different properties of the surface. Tables usually give Rz ≈ 4 × Ra, but on real surfaces Rz can range from about 4 to 7 times Ra. If the drawing specifies Rz, the surface must be measured as Rz; the table value is only a guide.
N grades
The N1–N12 roughness grades in ISO 1302 express Ra with a single number: N6 = Ra 0.8 µm, N7 = Ra 1.6 µm, N8 = Ra 3.2 µm. Each grade is about twice the previous one. ISO 1302 has been replaced by ISO 21920-1 and new drawings should state Ra directly; N grades are still common on older drawings.
Frequently asked questions
What is the difference between Ra and Rz?
Ra is the average deviation from the mean line; Rz is the average peak-to-valley height. On the same surface Rz is always larger than Ra; tables usually take it as about four times Ra.
What Ra is N7?
N7 = Ra 1.6 µm (about 63 µin). N6 = Ra 0.8 µm and N8 = Ra 3.2 µm.
What Rz is Ra 3.2?
Tables give Rz ≈ 12.5 µm for Ra 3.2 µm. The real value depends on the surface and can be higher; measure Rz if it is required.
How do you convert Ra from µm to µin?
Multiply micrometres by 39.37: Ra 0.8 µm ≈ 32 µin, Ra 1.6 µm ≈ 63 µin. Divide by 39.37 to go from microinches to micrometres.