PRECISION IN MATERIAL. CLARITY IN SUPPLY.

SHEET METAL

Sheet metal flat length: bend allowance and K-factor

Enter the thickness, inside bend radius, angle and outside dimensions to calculate the blank length to cut before bending. You can also find the K-factor from a test bend and the developed length of a rolled cylinder.

Flat length

Part shape

Outside legs are measured from the outer surface to the virtual sharp. The bend angle is the angle the sheet turns through (90° for a right angle). The K value is an example; enter your own.

L = Σ a − n × BD

Flat length

76.52 mm50 + 30 − 1 × 3.48
Bend allowance (BA)
4.52 mm
Bend deduction (BD)
3.48 mm
Outside setback (OSSB)
4 mm
Flat length: 76.52 mm (BA 4.52 mm, BD 3.48 mm)

How is the flat length calculated?

When sheet is bent the outer surface stretches and the inner surface shortens; the layer whose length does not change is the neutral axis. The flat length is the sum of the straight parts and the bend arcs measured along the neutral axis. Working from outside dimensions, the bend deduction (BD) is subtracted from their sum at each bend.

Example: 2 mm sheet, 2 mm inside radius, 90° bend, K = 0.44. Bend allowance BA = π × (2 + 0.44 × 2) × 90 / 180 ≈ 4.52 mm, outside setback OSSB = tan 45° × (2 + 2) = 4 mm, bend deduction BD = 2 × OSSB − BA ≈ 3.48 mm. An L part with outside legs of 50 and 30 mm has a flat length of 50 + 30 − 3.48 ≈ 76.52 mm.

What is the K-factor?

The K-factor is the distance of the neutral axis from the inside surface divided by the thickness (K = t / s). With the neutral axis exactly in the middle K = 0.5; because the neutral axis moves towards the inside during bending, the real value is usually below that. K depends on the material, thickness, inside radius to thickness ratio, die opening and bending method (air bending, bottoming), so the most reliable value comes from a test bend on your own press brake.

How to calculate the K-factor

Cut a strip of known length, bend it and measure both outside legs. In the calculator’s “K-factor” mode enter the flat length and the measured legs: BD = a + b − L, BA = 2 × OSSB − BD and K = (BA × 180 / (π × A) − r) / s. Use this K for later parts in the same material, thickness and tooling.

Rolled cylinder development

The developed length of sheet rolled into a cylinder or pipe uses the mean diameter: L = π × (D_outside − s). For large-radius rolling the neutral axis is taken at mid-thickness. For a 3 mm sheet rolled to a 200 mm outside diameter the length is ≈ π × 197 ≈ 618.9 mm.

Frequently asked questions

How do you calculate sheet metal flat length?

Subtract the bend deduction for each bend from the sum of the outside dimensions: L = a + b − BD, where BD = 2 × tan(A/2) × (r + s) − π × (r + K × s) × A / 180.

What K-factor should I use?

K lies between 0 and 0.5 and is not a constant; it varies with material, thickness, inside radius and tooling. As the inside radius gets smaller relative to the thickness, K decreases. The most accurate value is the one calculated from a test bend on your own press brake.

What is the difference between bend allowance and bend deduction?

Bend allowance (BA) is the length of the bend arc along the neutral axis and is added to the straight lengths. Bend deduction (BD) is subtracted from the sum of the outside dimensions: BD = 2 × OSSB − BA.

How do you calculate the blank for a rolled cylinder?

Use the mean diameter: L = π × (D_outside − s). For a 200 mm outside diameter and 3 mm sheet, L ≈ 618.9 mm.