PRODUCT TOLERANCES
Sheet and plate thickness tolerance chart
Enter thickness and width to see the permitted thickness range for cold-rolled stainless sheet, hot-rolled plate or ASTM A480.
Dimension and tolerance
Standard
Cold-rolled stainless wide strip and sheet; 0.3–8 mm thick, 600–2100 mm wide.
PRODUCT TOLERANCE
Size limits
Thickness
Method B · normal- Minimum size
- 0.93 mm
- Maximum size
- 1.07 mm
- Lower deviation
- −0.07 mm
- Upper deviation
- +0.07 mm
- Tolerance width
- 0.14 mm
The result shows size limits only; form tolerances not listed, flatness and surface condition are not covered. Use the current edition of the standard for orders.
Sheet and plate thickness tolerance chart
Thickness tolerances for cold-rolled stainless sheet (EN ISO 9445-2), hot-rolled plate (EN 10029) and ASTM A480. Width columns are upper limits: “≤ 1300” means over 1000 up to 1300 mm.
EN ISO 9445-2 thickness tolerance, method B (Table 2)± mm · normal and special (S) by width
| Thickness (mm) | N ≤ 1000 | N ≤ 1300 | N ≤ 2100 | S ≤ 1000 | S ≤ 1300 | S ≤ 2100 |
|---|---|---|---|---|---|---|
| < 0.3 | ± 0.03 | — | — | ± 0.03 | — | — |
| 0.3 – < 0.4 | ± 0.04 | ± 0.04 | — | ± 0.03 | ± 0.035 | — |
| 0.4 – < 0.5 | ± 0.04 | ± 0.04 | — | ± 0.035 | ± 0.035 | — |
| 0.5 – < 0.6 | ± 0.045 | ± 0.05 | — | ± 0.035 | ± 0.035 | — |
| 0.6 – < 0.8 | ± 0.05 | ± 0.05 | — | ± 0.04 | ± 0.04 | — |
| 0.8 – < 1 | ± 0.055 | ± 0.06 | ± 0.07 | ± 0.04 | ± 0.05 | ± 0.05 |
| 1 – < 1.2 | ± 0.06 | ± 0.07 | ± 0.08 | ± 0.05 | ± 0.055 | ± 0.06 |
| 1.2 – < 1.5 | ± 0.08 | ± 0.08 | ± 0.1 | ± 0.055 | ± 0.06 | ± 0.06 |
| 1.5 – < 2 | ± 0.08 | ± 0.09 | ± 0.11 | ± 0.065 | ± 0.07 | ± 0.08 |
| 2 – < 2.5 | ± 0.09 | ± 0.11 | ± 0.13 | — | — | — |
| 2.5 – < 3 | ± 0.11 | ± 0.13 | ± 0.15 | — | — | — |
| 3 – < 4 | ± 0.14 | ± 0.15 | ± 0.16 | — | — | — |
| 4 – < 5 | ± 0.15 | ± 0.17 | ± 0.19 | — | — | — |
| 5 – < 6 | ± 0.17 | ± 0.2 | ± 0.23 | — | — | — |
| 6 – 8 | ± 0.17 | ± 0.22 | ± 0.25 | — | — | — |
EN ISO 9445-2 thickness tolerance, method A (Table 1)± mm · normal for all widths, special (S) by width
| Thickness (mm) | N ≤ 2100 | S ≤ 1000 | S ≤ 1300 | S ≤ 2100 |
|---|---|---|---|---|
| 0.3 – < 0.5 | ± 0.04 | ± 0.025 | ± 0.03 | — |
| 0.5 – < 0.6 | ± 0.05 | ± 0.03 | ± 0.035 | — |
| 0.6 – < 0.8 | ± 0.05 | ± 0.035 | ± 0.04 | — |
| 0.8 – < 1 | ± 0.06 | ± 0.04 | ± 0.045 | ± 0.05 |
| 1 – < 1.2 | ± 0.07 | ± 0.045 | ± 0.045 | ± 0.05 |
| 1.2 – < 1.5 | ± 0.08 | ± 0.05 | ± 0.055 | ± 0.06 |
| 1.5 – < 2 | ± 0.09 | ± 0.055 | ± 0.06 | ± 0.07 |
| 2 – < 2.5 | ± 0.1 | — | — | — |
| 2.5 – < 3 | ± 0.12 | — | — | — |
| 3 – < 4 | ± 0.14 | — | — | — |
| 4 – < 5 | ± 0.15 | — | — | — |
| 5 – < 6.5 | ± 0.15 | — | — | — |
| 6.5 – 8 | ± 0.17 | — | — | — |
EN 10029 plate thickness tolerancelower / upper, mm
| Thickness (mm) | A | B | C | D |
|---|---|---|---|---|
| 3 – < 5 | −0.4 / +0.8 | −0.3 / +0.9 | 0 / +1.2 | ± 0.6 |
| 5 – < 8 | −0.4 / +1.1 | −0.3 / +1.2 | 0 / +1.5 | ± 0.75 |
| 8 – < 15 | −0.5 / +1.2 | −0.3 / +1.4 | 0 / +1.7 | ± 0.85 |
| 15 – < 25 | −0.6 / +1.3 | −0.3 / +1.6 | 0 / +1.9 | ± 0.95 |
| 25 – < 40 | −0.8 / +1.4 | −0.3 / +1.9 | 0 / +2.2 | ± 1.1 |
| 40 – < 80 | −1 / +1.8 | −0.3 / +2.5 | 0 / +2.8 | ± 1.4 |
| 80 – < 150 | −1 / +2.2 | −0.3 / +2.9 | 0 / +3.2 | ± 1.6 |
| 150 – 250 | −1.2 / +2.4 | −0.3 / +3.3 | 0 / +3.6 | ± 1.8 |
ASTM A480 cold-rolled sheet thickness tolerance (Table A2.5)± mm by width; between rows the next higher thickness applies
| Thickness | w ≤ 1000 | w ≤ 1300 | w ≤ 2100 |
|---|---|---|---|
| 0.3 mm (0.012") | ± 0.03 | — | — |
| 0.4 mm (0.016") | ± 0.04 | ± 0.04 | — |
| 0.5 mm (0.02") | ± 0.04 | ± 0.04 | — |
| 0.6 mm (0.024") | ± 0.05 | ± 0.05 | — |
| 0.8 mm (0.032") | ± 0.05 | ± 0.05 | — |
| 1 mm (0.04") | ± 0.06 | ± 0.06 | ± 0.08 |
| 1.2 mm (0.047") | ± 0.08 | ± 0.08 | ± 0.08 |
| 1.5 mm (0.059") | ± 0.08 | ± 0.08 | ± 0.1 |
| 2 mm (0.079") | ± 0.1 | ± 0.1 | ± 0.11 |
| 2.5 mm (0.098") | ± 0.1 | ± 0.1 | ± 0.13 |
| 3 mm (0.118") | ± 0.13 | ± 0.13 | ± 0.15 |
| 4 mm (0.157") | ± 0.17 | ± 0.17 | ± 0.17 |
| 5 mm (0.197") | ± 0.17 | ± 0.17 | ± 0.19 |
| 6 mm (0.236") | ± 0.17 | ± 0.2 | ± 0.23 |
| 8 mm (0.3125") | ± 0.17 | ± 0.23 | ± 0.25 |
Worked examples
- 1 mm stainless sheet, 1250 mm wide, EN ISO 9445-2 method B normal: ±0.07 mm, so 0.93–1.07 mm. Special (S) tolerance: ±0.055 mm.
- 10 mm hot-rolled plate, EN 10029 class A: −0.5 / +1.2 mm, so 9.5–11.2 mm. Class D: ±0.85 mm.
- 2 mm sheet, 1500 mm wide, ASTM A480 (Table A2.5): ±0.11 mm.
Which standard for which sheet?
Cold-rolled stainless wide strip and sheet (0.3–8 mm, 600–2100 mm wide) is toleranced to EN ISO 9445-2. Hot-rolled steel plate 3 mm and over follows EN 10029, and stainless sheet and plate to American specifications follows ASTM A480.
EN ISO 9445-2: method A, method B and special tolerance
Because measuring practice differs between countries, the standard gives two tables: method A (Table 1) and method B (Table 2). The method and tolerance type are stated on the order; normal tolerance applies otherwise. The special (S) tolerance is tighter and defined only below 2 mm.
EN 10029 plate thickness classes
EN 10029 defines four classes: in A the minus tolerance depends on thickness, in B it is a fixed −0.3 mm, in C it is zero (plus only) and in D the tolerance is symmetric. All four have the same total width at a given thickness; the class only shifts the band.
Frequently asked questions
What is the sheet thickness tolerance?
It depends on thickness, width and standard. Cold-rolled 1 mm stainless sheet (1250 mm, EN ISO 9445-2 method B) is ±0.07 mm; 10 mm hot-rolled plate (EN 10029 A) is −0.5 / +1.2 mm.
What is the difference between EN 10029 class A and class B?
In A the minus tolerance changes with thickness; in B it is −0.3 mm at every thickness. At 10 mm A is −0.5 / +1.2 mm and B −0.3 / +1.4 mm; the total width is the same.
What are methods A and B in EN ISO 9445-2?
They are two thickness measuring practices, each with its own table (Table 1 and Table 2). The order states which one applies.
What is the sheet width tolerance?
In EN ISO 9445-2 mill-edge sheet and strip are toleranced in width on the plus side only: +25 / 0 mm for 600–1000 mm and +30 / 0 mm for 1000–2100 mm.
Does thickness tolerance change sheet weight?
Yes; weight is directly proportional to thickness. On 1 mm sheet a ±0.07 mm tolerance can change weight by about ±7 %. Theoretical weight uses the nominal thickness.