PRECISION IN MATERIAL. CLARITY IN SUPPLY.

TIGHTENING TORQUE

Bolt torque chart: 8.8, 10.9 and 12.9

Choose the bolt diameter and property class to see the recommended tightening torque in Nm, kgf·m and ft·lbf. Values follow VDI 2230 for a total friction coefficient μ = 0.12.

Bolt

Diameter

Property class

For metric coarse bolts with a total friction coefficient μ = 0.12 (lightly oiled or zinc plated). Use a VDI 2230 calculation or manufacturer data for other friction conditions or critical joints.

VDI 2230 · μ = 0.12

M10 · 8.8

48 Nmtightening torque
kgf·m
4.89
ft·lbf
35.4
M10 8.8: 48 Nm (4.89 kgf·m, 35.4 ft·lbf), μ = 0.12

Metric bolt torque table

Tightening torques for metric coarse bolts per VDI 2230, total friction coefficient μ = 0.12.

Tightening torque, Nm (μ = 0.12)8.8 · 10.9 · 12.9, Nm and kgf·m for 8.8
Size8.8 (Nm)10.9 (Nm)12.9 (Nm)8.8 (kgf·m)
M434.65.10.31
M55.98.6100.6
M610.114.917.41.03
M824.636.142.22.51
M104871834.89
M12841231448.57
M1413319522913.56
M1620630235421.01
M1829542149230.08
M2041559269242.32
M2256780794557.82
M247141,0171,19072.81

Why tightening torque matters

What holds a bolted joint together is the preload created by stretching the bolt. Most of the torque applied with a torque wrench is used to overcome friction in the thread and under the head; only a small part becomes preload. The same torque therefore gives very different preloads depending on friction.

What μ = 0.12 means

The values are for a total friction coefficient μ = 0.12, a common assumption for lightly oiled, plain or zinc-plated bolts. With lubricated or friction-reducing coated bolts friction drops and the same torque gives a higher preload; dry or rough surfaces do the opposite. For other friction conditions or critical joints, determine the values by VDI 2230 calculation or from the bolt manufacturer.

Stainless steel bolts

Stainless bolts such as A2-70 and A4-80 have lower yield strength than carbon steel bolts, tend to gall in the thread and have a different friction coefficient. Because sources give stainless torques with different friction assumptions, this page does not list them; use the bolt manufacturer’s table and apply anti-seize where needed.

Frequently asked questions

What is the tightening torque for an M6 bolt?

For μ = 0.12, an M6 bolt takes 10.1 Nm in class 8.8, 14.9 Nm in 10.9 and 17.4 Nm in 12.9.

What is the tightening torque for an M8 bolt?

For μ = 0.12, an M8 bolt takes 24.6 Nm in class 8.8, 36.1 Nm in 10.9 and 42.2 Nm in 12.9.

What is the tightening torque for an M10 bolt?

For μ = 0.12, an M10 bolt takes 48 Nm in class 8.8, 71 Nm in 10.9 and 83 Nm in 12.9.

What is the tightening torque for an M12 bolt?

For μ = 0.12, an M12 bolt takes 84 Nm in class 8.8, 123 Nm in 10.9 and 144 Nm in 12.9.

What is the tightening torque for an M16 bolt?

For μ = 0.12, an M16 bolt takes 206 Nm in class 8.8, 302 Nm in 10.9 and 354 Nm in 12.9.

How do you convert Nm to kgf·m?

Divide Nm by 9.807: 48 Nm ≈ 4.9 kgf·m. For ft·lbf multiply Nm by 0.7376.