PRECISION IN MATERIAL. CLARITY IN SUPPLY.

GRADE COMPARISON

Material comparison and alternative grade finder

Choose two or three grades to see the key differences in short sentences, ratings for corrosion, strength, machinability, welding and heat, tensile strength and hardness, and their W.Nr, AISI and UNS identities side by side. Chemical composition and physical properties (thermal expansion, conductivity, elasticity) open on request.

Grades to compare

GRADE 1

304

Stainless Steel · 1.4301 · S30400

GRADE 2

316

Stainless Steel · 1.4401 · S31600

Common comparisons:Duplex 2205 – 316L316Ti – 316L304 – 32117-4 PH – 316410 – 420904L – 316L303 – 4164130 – 4140321 – 316304 – 310S254 SMO – 904L420 – 440C

In-depth guide:304 vs 316 stainless steel: the differences

Key differences

WHERE IT LEADS304

Estimated price: reference

No property where it leads

WHERE IT LEADS316

Estimated price: 75% dearer than 304

  • Corrosion resistance

Equal: Strength · Machinability · Weldability · Heat resistance

Property differences

Corrosion resistance

316 better

304
PREN 19.3
316
PREN 25.7

More resistant to pitting; the difference shows in chlorides (salt water, marine air).

Main composition differences

Molybdenum (Mo)

316 contains it, 304 does not

304
none
316
2–2.5

Improves resistance to pitting and crevice corrosion in chlorides.

Nickel (Ni)

More in 316

304
8–10.5
316
10–13

Stabilises the austenitic structure; improves toughness and formability.

Chromium (Cr)

More in 304

304
17.5–19.5
316
16.5–18.5

The element that makes steel stainless; more chromium means better corrosion resistance.

Property304316
Corrosion3/5PREN 19.34/5PREN 25.7
Strength1/5270 MPa · plate, annealed1/5260 MPa · plate, annealed
Machinability3/5index 0.523/5steel type class
Welding5/5steel type class5/5steel type class
Heat4/5925 °C · continuous, in air4/5925 °C · continuous, in air
Estimated price (vs 304)reference75% dearer
Critical pitting temperature (ASTM G48 E)10 °C20 °C
Critical crevice temperature (ASTM G48 F)<0 °C<0 °C
Tensile strength (Rm)600 MPa570 MPa
Elongation55 %55 %
Hardness175 HB170 HB
HardeningNone (cold work)None (cold work)
MagneticNoNo
Material groupStainless SteelStainless Steel
Material no. (W.Nr)1.43011.4401
EN nameX5CrNi18-10X5CrNiMo17-12-2
AISI304316
UNSS30400S31600
JISSUS304SUS316
Density7.9 g/cm³8 g/cm³
PREN17.5–21.123.1–28.4

Ratings are the sourced values of the stainless steel grade chart. Rm, elongation and hardness: Outokumpu typical values at room temperature (HB hot-rolled, HRB cold-rolled product). Grade chart · Hardness conversion

Critical temperatures: Outokumpu Handbook (2013) Table 6:1 typical values; higher is better. They rank grades in a standard test and are not a service limit.

Estimated price: based on the 12-month average alloy surcharge; size, quantity and cutting are not included. How is the price set? · Request a quotation

Chemical composition, %
Element304316
C≤ 0.07≤ 0.07
Si≤ 1≤ 1
Mn≤ 2≤ 2
P≤ 0.045≤ 0.045
S≤ 0.03≤ 0.03
Cr17.5–19.516.5–18.5▼
Ni8–10.510–13▲
Mo–2–2.5▲
N≤ 0.1≤ 0.1

Arrows mark elements markedly higher (▲) or lower (▼) than in grade 1. Values are the composition limits on the grade pages.

Physical properties · 20 °C
Property304316
Modulus of elasticity, GPa200200
Thermal expansion 20–200 °C, 10⁻⁶/K16.516.5
Thermal expansion 20–400 °C, 10⁻⁶/K17.517.5
Thermal conductivity, W/(m·K)1515
Specific heat, J/(kg·K)500500
Electrical resistivity, Ω·mm²/m0.730.75

Source: EN 10088-1:2005 (Euro Inox tables of technical properties). Values are for the annealed condition at 20 °C. Thermal expansion calculator

Alternatives to 304

The compositionally closest grades in the same material group. Choose one to open it as grade 2.

A close composition does not make a grade a direct substitute; check mechanical properties, the product standard and the specification.

304 – 316: Cr, Ni, Mo

How to compare grades

When comparing two grades, start with the chemical composition: carbon affects strength and weldability, chromium and molybdenum corrosion resistance, nickel the austenitic structure and toughness, nitrogen strength and pitting resistance. The table places the composition limits from the grade pages side by side and marks the elements where grade 2 is markedly higher or lower. PREN expresses the difference in pitting resistance of stainless steels and nickel alloys as one number.

How alternatives are found

The list compares grades in the same material group by the average values of the main elements and ranks those with the smallest difference. Each alternative shows its most marked differences (e.g. “Mo +0.5”). This is compositional closeness, not equivalence: for substitution, check mechanical properties, the product standard, heat treatment condition and specification. For the names of the same grade in other standards, see the steel equivalent chart.

Frequently asked questions

What is the difference between 304 and 316?

316 (1.4401) contains 2–2,5% molybdenum, while 304 (1.4301) has none. Molybdenum raises pitting resistance in chlorides: PREN is 17.5–21.1 for 304 and 23.1–28.4 for 316.

What is the difference between 316 and 316L?

316L (1.4404) has at most 0,03% carbon, 316 (1.4401) at most 0,07%. The lower carbon reduces the risk of intergranular corrosion after welding.

What is the difference between 2205 and 2507?

As a super duplex, 2507 (1.4410) has more chromium (24–26%), molybdenum (3–4,5%) and nitrogen; 2205 (1.4462) has 21–23% Cr and 2,5–3,5% Mo. PREN is 30.9–38.1 for 2205 and 37.7–46.5 for 2507.

What is the difference between 17-4 PH and 15-5 PH?

Both are copper-bearing precipitation hardening martensitic stainless steels. 17-4 PH (1.4542) has 15–17,5% Cr and 15-5 PH (1.4545) 14–15,5%; the lower delta-ferrite structure of 15-5 PH improves transverse toughness.