PRECISION IN MATERIAL. CLARITY IN SUPPLY.

GRADE COMPARISON

17-4 PH vs 316 stainless steel

17-4 PH is a copper-bearing martensitic stainless steel hardened by ageing; 316 is a molybdenum-bearing austenitic grade. 17-4 PH gives far higher strength, while molybdenum gives 316 better pitting resistance in chlorides (PREN 23.1–28.4 against 15–19.2).

Grades to compare

GRADE 1

17-4 PH

Stainless Steel · 1.4542 · S17400

GRADE 2

316

Stainless Steel · 1.4401 · S31600

Common comparisons:Duplex 2205 – 316L316Ti – 316L304 – 321410 – 420904L – 316L303 – 4164130 – 4140321 – 316304 – 310S254 SMO – 904L420 – 440C

Key differences

WHERE IT LEADS17-4 PH
  • Strength
WHERE IT LEADS316
  • Corrosion resistance

Property differences

Corrosion resistance

316 better

17-4 PH
PREN 17.1
316
PREN 25.7

More resistant to pitting; the difference shows in chlorides (salt water, marine air).

Strength

17-4 PH better

17-4 PH
850 MPa
316
260 MPa

Higher yield strength; carries the same load with a smaller section.

Main composition differences

Copper (Cu)

17-4 PH contains it, 316 does not

17-4 PH
3–5
316
none

Improves resistance in some acids; gives age hardening in PH grades.

Nickel (Ni)

More in 316

17-4 PH
3–5
316
10–13

Stabilises the austenitic structure; improves toughness and formability.

Molybdenum (Mo)

More in 316

17-4 PH
≤ 0.5
316
2–2.5

Improves resistance to pitting and crevice corrosion in chlorides.

Property17-4 PH316
Corrosion2/5PREN 17.14/5PREN 25.7
Strength4/5850 MPa · rod, annealed1/5260 MPa · plate, annealed
Machinability—3/5steel type class
Welding—5/5steel type class
Heat—4/5925 °C · continuous, in air
Critical pitting temperature (ASTM G48 E)–20 °C
Critical crevice temperature (ASTM G48 F)–<0 °C
Tensile strength (Rm)1100 MPa570 MPa
Elongation22 %55 %
Hardness–170 HB
HardeningAgeingNone (cold work)
MagneticYesNo
Material groupStainless SteelStainless Steel
Material no. (W.Nr)1.45421.4401
EN nameX5CrNiCuNb16-4X5CrNiMo17-12-2
AISI630316
UNSS17400S31600
JISSUS630SUS316
Density7.8 g/cm³8 g/cm³
PREN15–19.223.1–28.4

Ratings are the sourced values of the stainless steel grade chart. Rm, elongation and hardness: Outokumpu typical values at room temperature (HB hot-rolled, HRB cold-rolled product). Grade chart · Hardness conversion

Critical temperatures: Outokumpu Handbook (2013) Table 6:1 typical values; higher is better. They rank grades in a standard test and are not a service limit.

Chemical composition, %
Element17-4 PH316
C≤ 0.07≤ 0.07
Si≤ 1≤ 1
Mn≤ 1≤ 2▲
P≤ 0.04≤ 0.045
S≤ 0.03≤ 0.03
Cr15–17.516.5–18.5▲
Ni3–510–13▲
Mo≤ 0.52–2.5▲
N–≤ 0.1
Cu3–5–▼
Nb≥ 5 × C; ≤ 0.45–
FeBalance–

Arrows mark elements markedly higher (▲) or lower (▼) than in grade 1. Values are the composition limits on the grade pages.

Physical properties · 20 °C
Property17-4 PH316
Modulus of elasticity, GPa200200
Thermal expansion 20–200 °C, 10⁻⁶/K–16.5
Thermal expansion 20–400 °C, 10⁻⁶/K–17.5
Thermal conductivity, W/(m·K)1615
Specific heat, J/(kg·K)500500
Electrical resistivity, Ω·mm²/m0.710.75

Source: EN 10088-1:2005 (Euro Inox tables of technical properties). Values are for the annealed condition at 20 °C. Thermal expansion calculator

Alternatives to 17-4 PH

The compositionally closest grades in the same material group. Choose one to open it as grade 2.

A close composition does not make a grade a direct substitute; check mechanical properties, the product standard and the specification.

17-4 PH – 316: Mn, Cr, Ni, Mo, Cu

Frequently asked questions

Is 17-4 PH or 316 more corrosion resistant?

316 is more resistant in chlorides. The general corrosion resistance of 17-4 PH is close to 304 and depends on the ageing condition.

When is 17-4 PH chosen over 316?

For shafts, pump, valve and aerospace parts needing high strength and hardness. Because ageing is done at low temperature, parts can be machined close to size and hardened with little distortion.

Is 17-4 PH magnetic?

Yes, its martensitic structure is magnetic. Annealed 316 is not.