Duplex 2205 better
- Duplex 2205
- PREN 34.5
- 316L
- PREN 26.6
More resistant to pitting; the difference shows in chlorides (salt water, marine air).
GRADE COMPARISON
Duplex 2205 is a two-phase stainless steel of austenite and ferrite. With more chromium, molybdenum and nitrogen its PREN is clearly higher than 316L (30.9–38.1 against 23.1–30). Its typical yield strength is about twice as high (510 against 260 MPa), allowing thinner sections.
Stainless Steel · 1.4462 · S32205
Stainless Steel · 1.4404 · S31603
Equal: Machinability
Duplex 2205 better
More resistant to pitting; the difference shows in chlorides (salt water, marine air).
Duplex 2205 better
Higher yield strength; carries the same load with a smaller section.
316L better
Better suited to welding, with fewer precautions.
316L better
Works at higher temperature in air without scaling or embrittlement.
Duplex 2205 expands less
Changes length less with temperature; matters when joining dissimilar materials and in hot-running parts.
More in 316L
Stabilises the austenitic structure; improves toughness and formability.
More in Duplex 2205
The element that makes steel stainless; more chromium means better corrosion resistance.
More in Duplex 2205
Raises strength and pitting resistance.
| Property | Duplex 2205 | 316L |
|---|---|---|
| Corrosion | ||
| Strength | ||
| Machinability | ||
| Welding | ||
| Heat | ||
| Critical pitting temperature (ASTM G48 E) | 40 °C | 20 °C |
| Critical crevice temperature (ASTM G48 F) | 20 °C | <0 °C |
| Tensile strength (Rm) | 750 MPa | 570 MPa |
| Elongation | 35 % | 55 % |
| Hardness | 230 HB | 170 HB |
| Hardening | None (cold work) | None (cold work) |
| Magnetic | Yes | No |
| Material group | Stainless Steel | Stainless Steel |
| Material no. (W.Nr) | 1.4462 | 1.4404 |
| EN name | X2CRNIMON22-5-3 | X2CrNiMo17-12-2 |
| AISI | – | 316L |
| UNS | S32205 | S31603 |
| JIS | SUS329J3L | SUS316L |
| Density | 7.8 g/cm³ | 8 g/cm³ |
| PREN | 30.9–38.1 | 23.1–30 |
Ratings are the sourced values of the stainless steel grade chart. Rm, elongation and hardness: Outokumpu typical values at room temperature (HB hot-rolled, HRB cold-rolled product). Grade chart · Hardness conversion
Critical temperatures: Outokumpu Handbook (2013) Table 6:1 typical values; higher is better. They rank grades in a standard test and are not a service limit.
| Element | Duplex 2205 | 316L |
|---|---|---|
| C | ≤ 0.03 | ≤ 0.03 |
| Si | ≤ 1 | ≤ 1 |
| Mn | ≤ 2 | ≤ 2 |
| P | ≤ 0.035 | ≤ 0.045 |
| S | ≤ 0.015 | ≤ 0.03 |
| Cr | 21–23 | 16.5–18.5▼ |
| Ni | 4.5–6.5 | 10–13▲ |
| Mo | 2.5–3.5 | 2–3▼ |
| N | 0.1–0.22 | ≤ 0.1▼ |
Arrows mark elements markedly higher (▲) or lower (▼) than in grade 1. Values are the composition limits on the grade pages.
| Property | Duplex 2205 | 316L |
|---|---|---|
| Modulus of elasticity, GPa | 200 | 200 |
| Thermal expansion 20–200 °C, 10⁻⁶/K | 13.5 | 16.5 |
| Thermal expansion 20–400 °C, 10⁻⁶/K | – | 17.5 |
| Thermal conductivity, W/(m·K) | 15 | 15 |
| Specific heat, J/(kg·K) | 500 | 500 |
| Electrical resistivity, Ω·mm²/m | 0.80 | 0.75 |
Source: EN 10088-1:2005 (Euro Inox tables of technical properties). Values are for the annealed condition at 20 °C. Thermal expansion calculator
The compositionally closest grades in the same material group. Choose one to open it as grade 2.
A close composition does not make a grade a direct substitute; check mechanical properties, the product standard and the specification.
In chlorides and where strength matters, yes: it resists pitting and stress corrosion cracking better. 316L is easier to form and weld, and austenitic grades are chosen over duplex for continuous service above about 250 °C.
Yes. About half of its structure is ferrite, so 2205 is magnetic; annealed 316L is not.
Heat input and interpass temperature are limited and a duplex filler is used to keep the ferrite–austenite balance. 316L has no such narrow window.