303 better
- 303
- PREN 18.8
- 416
- PREN 14.0
More resistant to pitting; the difference shows in chlorides (salt water, marine air).
GRADE COMPARISON
303 and 416 are free-machining stainless steels with added sulphur (S 0.15–0.35%). 303 is austenitic, with better corrosion resistance and no magnetism. 416 is martensitic: it can be hardened, is magnetic and has a slightly higher machinability index (0.95 against 0.85).
Stainless Steel · 1.4305 · S30300
Stainless Steel · 1.4005 · S41600
Equal: Machinability
303 better
More resistant to pitting; the difference shows in chlorides (salt water, marine air).
416 better
Higher yield strength; carries the same load with a smaller section.
303 better
Better suited to welding, with fewer precautions.
303 better
Works at higher temperature in air without scaling or embrittlement.
416 expands less
Changes length less with temperature; matters when joining dissimilar materials and in hot-running parts.
303 contains it, 416 does not
Stabilises the austenitic structure; improves toughness and formability.
More in 303
The element that makes steel stainless; more chromium means better corrosion resistance.
More in 416
Raises strength and hardenability. Low carbon reduces the risk of intergranular corrosion after welding.
| Property | 303 | 416 |
|---|---|---|
| Corrosion | ||
| Strength | ||
| Machinability | ||
| Welding | ||
| Heat | ||
| Tensile strength (Rm) | 585 MPa | 550 MPa |
| Elongation | 35 % | 20 % |
| Hardness | – | – |
| Hardening | None (cold work) | Quench and temper |
| Magnetic | No | Yes |
| Material group | Stainless Steel | Stainless Steel |
| Material no. (W.Nr) | 1.4305 | 1.4005 |
| EN name | X8CrNiS18-9 | X12CrS13 |
| AISI | 303 | 416 |
| UNS | S30300 | S41600 |
| JIS | SUS303 | SUS416 |
| Density | 7.9 g/cm³ | 7.7 g/cm³ |
| PREN | 17–20.6 | 12–16 |
Ratings are the sourced values of the stainless steel grade chart. Rm, elongation and hardness: Outokumpu typical values at room temperature (HB hot-rolled, HRB cold-rolled product). Grade chart · Hardness conversion
| Element | 303 | 416 |
|---|---|---|
| C | ≤ 0.1 | 0.06–0.15▲ |
| Si | ≤ 1 | ≤ 1 |
| Mn | ≤ 2 | ≤ 1.5▼ |
| P | ≤ 0.045 | ≤ 0.04 |
| S | 0.15–0.35 | 0.15–0.35 |
| Cr | 17–19 | 12–14▼ |
| Ni | 8–10 | –▼ |
| Mo | – | ≤ 0.6 |
| N | ≤ 0.1 | – |
| Cu | ≤ 1 | – |
Arrows mark elements markedly higher (▲) or lower (▼) than in grade 1. Values are the composition limits on the grade pages.
| Property | 303 | 416 |
|---|---|---|
| Modulus of elasticity, GPa | 200 | 215 |
| Thermal expansion 20–200 °C, 10⁻⁶/K | 16.5 | 11.0 |
| Thermal expansion 20–400 °C, 10⁻⁶/K | 17.5 | 12.0 |
| Thermal conductivity, W/(m·K) | 15 | 30 |
| Specific heat, J/(kg·K) | 500 | 460 |
| Electrical resistivity, Ω·mm²/m | 0.73 | 0.60 |
Source: EN 10088-1:2005 (Euro Inox tables of technical properties). Values are for the annealed condition at 20 °C. Thermal expansion calculator
The compositionally closest grades in the same material group. Choose one to open it as grade 2.
A close composition does not make a grade a direct substitute; check mechanical properties, the product standard and the specification.
416 machines slightly more easily: its BSSA machinability index is 0.95 against 0.85 for 303. Both cut far more easily than standard stainless (304: 0.52).
Choose 303 for corrosion resistance and a non-magnetic part; 416 for hardness, wear resistance or magnetism. Because of sulphur, neither suits welding or chlorides.
Yes, it is martensitic and magnetic. Annealed 303 is not.