PRECISION IN MATERIAL. CLARITY IN SUPPLY.

STAINLESS STEEL FAMILY

Martensitic stainless steels and their properties

Martensitic stainless steels are the stainless family that can be hardened by heat treatment. 410, the 420 variants, 431 and 440C are used for shafts, valve parts, cutting edges and wear surfaces.

What is martensitic stainless steel?

Martensitic grades are hardened by heating and rapid cooling; a second heating called tempering then sets the balance of hardness and toughness. The main shape is usually machined in the softer annealed condition, and the final properties come from heat treatment.

Martensitic stainless steels are attracted to a magnet. Heat treatment can change dimensions and leave oxide on the surface, so allowance is left for final grinding on precision surfaces.

420 is not one steel: the effect of carbon

1.4021 (X20Cr13), 1.4028 (X30Cr13) and 1.4034 (X46Cr13) are three separate EN grades all called 420. More carbon raises the hardness and wear resistance reachable after heat treatment; 1.4021 suits load-bearing mechanical parts, the higher-carbon grades cutting and wear surfaces.

In 420F / 1.4029 sulfur eases machining. 431 / 1.4057 contains nickel, and 440C, with high carbon and hard carbides, is used on wear surfaces. Harder is not always better: impact, section thickness and the final heat treatment affect the result.

Welding and final surface

Hardenability also matters in welding: heating and cooling around the weld can change hardness in that zone, so the welding approach used for 304L does not carry over unchanged. Corrosion resistance depends not only on chromium but also on heat treatment and final cleaning.

Shafts, pumps and valve components

Shafts and valve parts are familiar applications of martensitic stainless steels. Chromium- and molybdenum-bearing grades such as 1.4122 are associated with this field. Grade 431 / 1.4057 is another option, containing nickel and recognised for strength and toughness. These components carry forces while remaining exposed to the surrounding medium. Stainless behaviour alone does not fully describe their material needs; it matters alongside mechanical properties. Similar shaft geometries can consequently be associated with different alloy balances.

Toughness is resistance to fracture. Two shafts of the same shape can have similar hardness without responding identically to impact. Heat treatment and alloy composition change the balance of these properties.

Bearings and precision contact surfaces

Bearing elements and injection components contain small surfaces operating within precise mechanisms. Hardness and wear resistance matter together with the corrosion behaviour of these surfaces. Nitrogen-alloyed 1.4123 is one of the grades associated with such applications. Grade 440C is also linked with hardness and wear service, but has a different carbon level and alloy balance. Appearing in related component categories does not make two grades the same material or give them identical properties.

Supermartensitic steels in oil and gas

Low-carbon supermartensitic steels are associated with high-strength oil and gas equipment. Grade 1.4415 belongs to the Super 13Cr family in this field. Nickel and molybdenum produce a different balance from conventional 13 percent chromium martensitic steels. Super 13Cr nevertheless identifies a broad family rather than one product or one UNS designation. Different product definitions occur within it. The broad commercial family name is therefore distinct from the identity of an individual EN grade.

Heat and mechanical loading in turbines

Steels intended for elevated-temperature strength, such as 1.4923, have a separate role in energy equipment. Turbine parts and hot fasteners are recognised applications. Their duty involves more than exposure to a hot surface: the material must also carry forces while hot. Furnace materials and turbine steels are therefore not interchangeable simply because both work with heat. The corrosion characteristics of 1.4923 also differ from those of general-purpose austenitic stainless steels.

The application balance distinguishing the grades

A shared martensitic family does not give every member the same properties. Different balances of carbon, chromium, nickel, molybdenum and nitrogen change the resulting material characteristics. Hardness may be prominent in one grade, toughness in another and elevated-temperature strength in a third. Describing a material only as hard or stainless leaves out this useful variety. Their applications show how related steels come to be associated with different technical roles and component types.

Molybdenum-bearing and aerospace designations

Grade 1.4120 / X20CrMo13 is a separate molybdenum-bearing martensitic steel used in energy equipment and industrial valve components. The steels associated with 420 do not all share one EN designation or composition. Older SEW 400 references and current product specifications also have different scopes.

Aerospace bar grade 1.4938 has a different composition containing nickel, molybdenum and vanadium. EN 4825:2021 defines it through a particular product form and condition. Hot-fastener grades such as 1.4913 instead focus on sustained loads in energy equipment. Their shared martensitic structure does not establish identical service limits.

Room-temperature data for a hot-fastener steel

A row for 1.4923 in EN 10269:2013 shows why test temperature matters. These values apply to +QT1 at diameters up to 160 mm. +QT means hardening followed by tempering, a controlled reheating treatment. Although the steel is used for hot fasteners, these figures do not describe its strength at every elevated temperature.

Property1.4923 / +QT1 reference
Rp0.2, minimum (MPa)600
Rm (MPa)800–950
Elongation A, minimum (%)14
Reduction of area Z, minimum (%)40
KV2 at 20°C, minimum (J)27
Sources and technical details

Source: EN 10269:2013, Table 4. Tensile tests are at room temperature; impact energy is given at 20°C. Rp0.2 is the stress at 0.2% permanent extension and Rm the highest tensile-test stress. Stress is force per cross-sectional area; MPa and N/mm² are equivalent. A describes elongation after fracture; Z the reduction in the fractured specimen’s cross-sectional area. KV2 is energy absorbed by an ISO-V-notched specimen in an impact test, in joules (J). Rectangular sections use dimension b instead of diameter d as specified by the standard. The row does not apply to +QT2 or every size, and does not replace design values for elevated temperature and sustained loading.

BSI — EN 10269:2013 — Table 4: 1.4923, +QT1, diameters up to 160 mm and room-temperature test conditions.

What does carbon content change?

Carbon affects the hardness and wear behaviour developed after suitable hardening. Higher-carbon steels can be considered where a cutting edge needs to retain its shape. Greater hardness does not mean better performance in every respect. Impact, part thickness and final heat treatment also affect the result.

Of these three, 1.4021 / X20Cr13 has the lower carbon content. X30Cr13 and X46Cr13 are the higher-carbon options. All three may be shaped in an annealed, softened condition and then heat treated to develop their final properties.

EN gradeSteel nameKey distinction
1.4021X20Cr13Lower carbon among the three options; 0.16–0.25% carbon
1.4028X30Cr13Higher carbon than 1.4021; 0.26–0.36% carbon
1.4034X46Cr13Higher carbon among the three options; 0.43–0.50% carbon
Sources and technical details

Source: EN 10088-3:2023, Table 5. The ranges are cast-analysis limits for long products such as bars, expressed in mass percent. This edition gives 0.26–0.36% carbon for 1.4028. The numbers are not hardness values or the analysis of a particular batch. Heat treatment, section size and treatment condition also affect final hardness.

EN 10088-3:2023 — official SIST preview (PDF) — The preview identifies the edition and scope. The chemical comparison follows the Table 5 rows and footnotes in the full text.

Outokumpu — Handbook of Stainless Steel, 2013 (PDF) — PDF pp.12, 15 and 73–74: martensitic structure, carbon effects and surface preparation.

Machining soft material before hardening

Annealing is a heat treatment used to soften the material. The main shape can be machined in this condition, with hardness developed later. Tempering after hardening is a separate heating stage used to adjust the balance of hardness and toughness. The steel name alone does not tell which of these treatments a finished part has received.

Heat treatment can change dimensions and form an oxide layer on the surface. A shaft or precise cutting surface that will be ground later is therefore left with some extra material. Final grinding removes this allowance to establish the required dimensions and surface.

Different needs in shafts and cutting parts

1.4021 can be considered for mechanical parts that need both load-carrying ability and corrosion resistance. Higher-carbon options can be useful for cutting and wearing surfaces. Contact area and the way the load is applied matter as well as material hardness.

A very thin cutting edge or inadequate support from the body can change the result. On a broad sliding surface, contact area and finish become important. Another option used in these applications is 440C, which has different carbon content and different hard carbide particles within its structure.

What changes in welding and bending?

The ability of 420 steels to harden also matters during welding. Heating and cooling around the weld can change local structure and hardness. An approach used for welding 304L therefore does not transfer directly to 420. Carbon content and the condition before welding also matter.

Bending, hole preparation and machining the main shape generally take place in a softer condition. Hardening may follow. If welding is involved, its heating and cooling also affect this sequence. Final mechanical properties develop together with heat treatment.

What distinguishes 420F / 1.4029?

420F / 1.4029 is a martensitic stainless steel with added sulfur to make turning and machining easier. It is used for small shafts, valve parts and fasteners. Its carbon range differs from 1.4021 and 1.4028. Easier machining from added sulfur does not remove the importance of corrosion and surface properties.

A mechanical-property table marked with a supply condition such as +QT850 describes material that has been hardened and tempered. The same values do not apply to a bar softened by annealing. The 420F page therefore gives its values together with product size and treatment condition.

Other EN designations in the 420 family

1.4031 / X39Cr13 and 1.4037 / X65Cr13 are also martensitic stainless steels with different carbon contents. 1.4035 / X46CrS13 also differs in its sulfur range. These are not different spellings of the same 420 steel. They are separate designations in the corrosion-resisting steel tables of EN 10088-3. Use in a blade or tool-like part does not alone establish a different material class.

The table compares carbon and sulfur contents under EN 10088-3:2023; it does not show hardness. Higher carbon can allow greater hardening after suitable heat treatment. An annealed bar and a hardened part do not have the same hardness. An exact HRC hardness value cannot be calculated from carbon content alone.

EN designationCarbonMaximum sulfur / sulfur range
1.4031 — X39Cr130.36–0.42%≤ 0.030%
1.4034 — X46Cr130.43–0.50%≤ 0.030%
1.4035 — X46CrS130.43–0.50%0.15–0.35%
1.4037 — X65Cr130.58–0.70%≤ 0.015%
Sources and technical details

This table also follows EN 10088-3:2023, Table 5. Carbon and sulphur are mass percentages; “≤” denotes a maximum and the dash between two numbers denotes a range. Sulphur’s effect on machining does not imply identical corrosion or welding behaviour across the grades.

EN 10088-3:2023 — official SIST preview (PDF) — The preview identifies the edition and scope. The chemical comparison follows the Table 5 rows and footnotes in the full text.

Grades in this family

17 grades

EN, AISI / SAE, UNS and JIS designations of the grades in this family. Designations from different systems do not always imply identical specification requirements.

Material grades: EN, AISI / SAE, UNS and JIS
Grade / AlloyEN / W.Nr.AISI / SAEUNSJISGrade page
Martensitic stainless steels17 grades
Grade page
416Machining-focused martensitic1.4005X12CrS13416S41600SUS416
410Martensitic · Heat-treat hardenable1.4006X12Cr13410S41000SUS410
420Martensitic · Hardenable1.4021X20Cr13 / X20Cr14420S42000SUS420J1
420Martensitic · X30Cr131.4028X30Cr13420S42000SUS420J2
420FMartensitic · Sulfur bearing420BF1.4029X29CrS13420FS42020SUS420F
420Martensitic · X46Cr131.4034X46Cr13—S42000—
431Nickel-alloyed martensitic grade1.4057X17CrNi16-2431S43100SUS431
1.4112High carbon · Wear resistance1.4112X90CrMoV18———
X50CrMoV15Hardenable · Molybdenum and vanadium1.4116X50CrMoV15———
1.4122Martensitic · Molybdenum bearing1.4122X39CrMo17-1 / X35CrMo17———
1.4123Martensitic · Nitrogen alloyed1.4123X40CrMoVN16-2—S42025—
440CHigh carbon · Wear resistance1.4125X105CrMo17440CS44004—
415Low-carbon martensitic1.4313X3CrNiMo13-4—S41500SUSF6NM
Super 13CrSupermartensitic · Low carbon1.4415X2CrNiMoV13-5-2———
X4CrNiMo16-5-1Low carbon · Strength and toughness1.4418X4CrNiMo16-5-1———
1.4923Martensitic · Elevated-temperature strength1.4923X22CrMoV12-1———
1.4938Martensitic · Aerospace bars1.4938X12CrNiMoV12-3———

Guides

Frequently asked questions

What is martensitic stainless steel?

The stainless family that can be hardened by heating and rapid cooling and then tempered. 410, 420, 431 and 440C are examples.

Which grade is 420 stainless?

420 is not one steel: 1.4021 (X20Cr13), 1.4028 (X30Cr13) and 1.4034 (X46Cr13) are separate EN grades that differ in carbon.

Is martensitic stainless magnetic?

Yes, martensitic stainless steels are attracted to a magnet. It is a natural property of their structure.

Where is martensitic stainless used?

Shafts, valve parts, pump components, cutting edges and wear surfaces such as bearings. The hardness–toughness balance is chosen through grade and heat treatment.

LET’S CLARIFY YOUR REQUIREMENT

Your next project.
The right starting point.

For European-origin material with an EN 10204 3.1 certificate, talk to our team directly about the supply options for your project.

Request a quote