PRECISION IN MATERIAL. CLARITY IN SUPPLY.

PRECIPITATION HARDENING STAINLESS

PH stainless steels: 17-4 PH, 15-5 PH and 13-8 PH

PH (precipitation hardening) stainless steels combine corrosion resistance with high mechanical strength. They gain strength through an ageing heat treatment and are used for pump shafts, valve parts, aerospace fasteners and mechanisms.

What is precipitation hardening?

PH is the stainless group in which heat treatment forms very small strengthening particles inside the metal. The treatment, done at a set temperature and time, is called ageing. The particles make permanent deformation under load harder, and strength rises.

PH is not a single structure. 17-4 PH, 15-5 PH, 13-8 Mo PH, Custom 455 and Custom 465 are martensitic PH grades. 17-7 PH and 15-7 Mo are semi-austenitic: their initially formable structure is conditioned by preparatory treatments before hardening, so their processing routes differ.

How PH steel differs from 304L and 316L

304L and 316L are widely used in tanks, piping and chemical equipment, valued for easy forming and suitability for welded construction. PH steels are chosen mainly for high strength: pump shafts, pins and aerospace connections must carry load and resist corrosion together.

A tank in constant contact with chemicals and a shaft carrying high loads do not need the same properties. Resisting corrosion and carrying load are separate properties, and stainless families combine them in different proportions. 304L and 316L are austenitic and respond little to a magnet; martensitic PH grades are attracted to one.

What do Condition A, H900, H1025 and H1150 mean?

Condition A is the state before ageing. Names such as H900 or H1150 denote specific aged conditions. The same grade gives different strength, ductility and toughness in different conditions; they are not separate steels.

17-4 PH and 15-5 PH are seen in H900, H925, H1025, H1075, H1100 and H1150. 13-8 PH has conditions from H950 to H1150. Suffixed names such as H1150D and H1150M are separate treatment sequences. The highest hardness is not the best condition for every part.

How 17-4 PH, 15-5 PH and 13-8 PH differ

17-4 PH is common in general machine parts. The composition of 15-5 PH is balanced to improve toughness and ductility across the bar (transverse direction), which matters in fasteners loaded from the side. 13-8 PH combines high strength with fracture resistance in heavy sections.

Equal tensile strength does not mean equal results: in the producer’s example both 17-4 PH and 15-5 PH reach 1379 MPa in H900. The difference lies in behaviour under impact, cracks and loads from different directions.

17-7 PH and 15-7 Mo for thin sections

17-7 PH and 15-7 Mo are used in springs, flexible elements and aerospace components where high strength meets thin sections. Sheet and strip are their main product forms. 15-7 Mo contains about 2–3 % molybdenum; the two steels are not names for the same material.

Stock, test specimen and finished component

A pin or connection body can develop its final strength after machining. A small test specimen may also be treated separately from the parent material. Three different conditions can therefore be relevant to the same metal. The example below illustrates the distinction.

Item in the exampleConditionWhat does it describe?
StockCondition AStarting state before ageing
Test specimenH1025Test condition of a separately aged small piece
Finished pin or bodyDepends on its final treatmentNot established by the specimen result alone
Sources and technical details

This is a hypothetical processing example, not a batch report or company delivery commitment. Cleveland-Cliffs’ May 2021 datasheet for 15-5 PH sheet and strip distinguishes Condition A starting material from later ageing conditions. Only that distinction is used here; numerical flat-product acceptance values are not transferred to bar or forgings.

H1150M and the two-stage H1150 + H1150 are also distinct treatment designations. The producer’s table lists separate routes. Detailed temperatures and times remain in the existing heat-treatment guide rather than being repeated in this introduction.

Cleveland-Cliffs — 15-5 PH, May 2021 (PDF) — pp.2–3: Condition A starting state and separate ageing routes for sheet and strip. The example table is not copied from a real certificate.

Carpenter — Custom 630 / 17-4, April 2024 (PDF) — p.8: H1150M and H1150D are used as distinct conditions. They are not one treatment applicable to every PH grade.

Surfaces, welding and corrosion resistance

A protective surface film contributes to stainless properties. Clean finishing after machining and heat treatment helps preserve it. Chlorides found in salts, liquid retained in narrow gaps and force concentrated in a small region affect corrosion, meaning damage from the surrounding environment.

Welding heat changes the structure around the joint. Weld metal, parent stock and the surrounding heat-affected region differ. The subsequent heat-treatment sequence therefore matters. A welded body and a shaft machined from solid bar can reach their final properties by different routes.

Grades in this family

11 grades

EN, AISI / SAE, UNS and JIS designations of the grades in this family. Designations from different systems do not always imply identical specification requirements.

Material grades: EN, AISI / SAE, UNS and JIS
Grade / AlloyEN / W.Nr.AISI / SAEUNSJISGrade page
PH stainless steels11 grades
Grade page
1.4530PH stainless · Strength and toughness1.4530X1CrNiMoAlTi12-9-2—S11800—
17-4 PHStrength adjusted through ageing1.4542X5CrNiCuNb16-4630S17400SUS630
1.4594PH stainless · Strength and toughness1.4594X5CrNiMoCuNb14-5———
1.4596PH stainless · Very low carbon1.4596X1CrNiMoAlTi12-10-2—S10120—
13-8 Mo PHToughness and transverse propertiesXM-131.4534X3CrNiMoAl13-8-2—S13800—
15-5 PHFerrite control · Transverse propertiesXM-121.4545X5CrNiCu15-5—S15500—
15-7 MoSemi-austenitic PH · Molybdenum bearing—632S15700—
17-7 PHStrength developed after forming1.4568X7CrNiAl17-7631S17700SUS631
AM 355Semi-austenitic structure · Delivery condition matters—634S35500—
Custom 455High yield strength · Precision fabrication1.4543—S45500—
Custom 465Balance of strength, toughness and corrosion behaviour1.4614—S46500—

Guides

Frequently asked questions

What is PH stainless steel?

A stainless steel that gains strength when an ageing heat treatment forms small strengthening particles inside the metal. 17-4 PH, 15-5 PH and 13-8 Mo PH are the best-known grades.

What does H900 mean?

H900 is an aged condition applied after Condition A in grades such as 17-4 PH and 15-5 PH. In the producer’s example 17-4 PH reaches 1379 MPa tensile strength in H900; conditions such as H1025 and H1150 offer a different balance of strength and toughness.

What is the difference between 17-4 PH and 15-5 PH?

Both are martensitic PH stainless steels and can reach the same tensile strength in H900. 15-5 PH is balanced for better transverse toughness and ductility; 17-4 PH is more common in general machine parts.

Is PH stainless steel magnetic?

Martensitic and most precipitation-hardenable stainless steels are attracted to a magnet. This is a property of their structure, not a sign of poor quality.

LET’S CLARIFY YOUR REQUIREMENT

Your next project.
The right starting point.

For European-origin material with an EN 10204 3.1 certificate, talk to our team directly about the supply options for your project.

Request a quote