WEIGHT CALCULATOR
Round bar weight calculator
Calculate round bar and shaft weight from diameter, length and quantity. A kg/m chart for 304, 316L, 2205, 6082 aluminium and Grade 5 titanium follows below.
Material selection
A general estimate for this material. Selecting a grade can provide a more specific density.
Custom density
Dimensions and quantity
Other
Leave empty to calculate weight only. The price is used for this calculation alone; no currency conversion is applied. Request a current price
All dimensions are in millimetres. Decimal points and commas are accepted.
How is the weight calculated?
The section area is multiplied by density to find kg/m. Piece weight uses the entered length; total weight also includes quantity.
π × d² / 4 = section area (mm²)
Area × density / 1000 = kg/m
kg/m × length (mm) / 1000 × quantity = total kgStainless steels
- Weight per metre
- 10.053 kg/m
- Weight per piece
- 10.053 kg
- Density used
- 8 g/cm³
A theoretical estimate. Actual dimensions, tolerances and material properties can change the measured weight.
Round bar weight chart
Theoretical weight from nominal dimensions and the typical densities used by the calculator (g/cm³ in brackets). Actual weight varies with size tolerance and grade; use these values for estimates, not for invoicing.
Round bar weight chartCarbon steel · 304 / 304L · 316L · Duplex 2205 · Aluminium 6082 · Titanium Grade 5 · kg/m · Ø5–Ø200 mm
| Diameter (mm) | Carbon steel (7.85) | 304 / 304L (7.90) | 316L (8.00) | Duplex 2205 (7.80) | Aluminium 6082 (2.70) | Titanium Grade 5 (4.42) |
|---|---|---|---|---|---|---|
| Ø5 | 0.154 | 0.155 | 0.157 | 0.153 | 0.053 | 0.087 |
| Ø6 | 0.222 | 0.223 | 0.226 | 0.221 | 0.076 | 0.125 |
| Ø8 | 0.395 | 0.397 | 0.402 | 0.392 | 0.136 | 0.222 |
| Ø10 | 0.617 | 0.620 | 0.628 | 0.613 | 0.212 | 0.347 |
| Ø12 | 0.888 | 0.893 | 0.905 | 0.882 | 0.305 | 0.500 |
| Ø15 | 1.387 | 1.396 | 1.414 | 1.378 | 0.477 | 0.781 |
| Ø16 | 1.578 | 1.588 | 1.608 | 1.568 | 0.543 | 0.889 |
| Ø20 | 2.466 | 2.482 | 2.513 | 2.450 | 0.848 | 1.389 |
| Ø25 | 3.853 | 3.878 | 3.927 | 3.829 | 1.325 | 2.170 |
| Ø30 | 5.549 | 5.584 | 5.655 | 5.513 | 1.909 | 3.124 |
| Ø35 | 7.553 | 7.601 | 7.697 | 7.504 | 2.598 | 4.253 |
| Ø40 | 9.865 | 9.927 | 10.05 | 9.802 | 3.393 | 5.554 |
| Ø45 | 12.48 | 12.56 | 12.72 | 12.41 | 4.294 | 7.030 |
| Ø50 | 15.41 | 15.51 | 15.71 | 15.32 | 5.301 | 8.679 |
| Ø60 | 22.20 | 22.34 | 22.62 | 22.05 | 7.634 | 12.50 |
| Ø70 | 30.21 | 30.40 | 30.79 | 30.02 | 10.39 | 17.01 |
| Ø80 | 39.46 | 39.71 | 40.21 | 39.21 | 13.57 | 22.22 |
| Ø90 | 49.94 | 50.26 | 50.89 | 49.62 | 17.18 | 28.12 |
| Ø100 | 61.65 | 62.05 | 62.83 | 61.26 | 21.21 | 34.71 |
| Ø120 | 88.78 | 89.35 | 90.48 | 88.22 | 30.54 | 49.99 |
| Ø150 | 138.72 | 139.60 | 141.37 | 137.84 | 47.71 | 78.11 |
| Ø200 | 246.62 | 248.19 | 251.33 | 245.04 | 84.82 | 138.86 |
Worked example
- Ø50 mm 316L round bar, 3 m: π × 50² ÷ 4 = 1963.5 mm²; 1963.5 × 8.00 ÷ 1000 = 15.71 kg/m; × 3 m = 47.12 kg.
Round bar weight formula
A round bar’s cross-section is π × d² ÷ 4. With the area in mm² and density in g/cm³, area × density ÷ 1000 gives kilograms per metre directly. For Ø50 mm 304 stainless the area is 1963.5 mm², so the weight is 1963.5 × 7.90 ÷ 1000 = 15.51 kg/m.
A handy shortcut for steels is kg/m ≈ d² × 0.00617 for carbon steel (7.85 g/cm³) and d² × 0.00620 for 304 (7.90 g/cm³). Doubling the diameter quadruples the weight, so even a small diameter difference matters on large bars.
Round bar weight formula in Excel
With the diameter (mm) in A2, length (mm) in B2 and density (g/cm³) in C2, the formula below returns the piece weight in kilograms.
=PI()*A2^2/4*C2/1000*B2/1000Diameter and surface condition
The calculation uses the nominal diameter. Cold-drawn, ground or peeled bars are very close to nominal size; hot-rolled and forged bars have wider tolerances and carry machining allowance, so a hot-rolled bar of the same nominal diameter can weigh slightly more than a ground one.
Round bar weight by material
At the same Ø50 mm diameter the weights per metre are: carbon steel 15.41 kg/m, 304 stainless 15.51 kg/m, 316L 15.71 kg/m, 2205 duplex 15.32 kg/m, 6082 aluminium 5.30 kg/m, Grade 2 titanium 8.86 kg/m. Stainless and carbon steel differ by less than 2%, while aluminium weighs about a third and titanium a little over half as much.
Solid bar or tube?
Where weight matters, a tube can replace a solid shaft. A Ø50 mm solid carbon steel bar is 15.41 kg/m while 50 × 5 mm tube is 5.55 kg/m, about 64% lighter. Torsional and bending strength depend far more on the outside diameter and drop less; the choice needs a strength calculation.
From weight to length: round bar
To find how many metres you have, divide the total weight by the weight per metre. Ø40 mm carbon steel bar weighs 9.86 kg/m, so 100 kg is about 10.1 metres and one tonne about 101 metres. This is how stock is estimated by weighing instead of counting lengths; size tolerance can shift the result by a few per cent.
Frequently asked questions
How much does a Ø50 stainless round bar weigh per metre?
15.71 kg/m in 316L and 15.51 kg/m in 304. The area is π × 50² ÷ 4 = 1963.5 mm²; area × density ÷ 1000 gives kg per metre.
What is the round bar weight formula?
kg/m = π × diameter² ÷ 4 × density (g/cm³) ÷ 1000. Multiply kg/m by the length in metres for one piece, and by the quantity for the total.
How much does a carbon steel round bar weigh per metre?
A Ø50 mm carbon steel bar is 15.41 kg/m and a Ø30 mm bar 5.55 kg/m (7.85 g/cm³).
How is aluminium round bar weight calculated?
The formula is the same with 2.70 g/cm³ for 6082. A Ø50 mm aluminium bar weighs 5.30 kg/m.
How do I read the round bar weight chart?
Rows are sizes and columns are materials; the number in brackets in each column heading is the density used (g/cm³). Each cell is the weight of one metre (kg/m). Multiply it by the length in metres for one piece and by the quantity for the total.
How do I calculate round bar weight in Excel?
With diameter in A2, length in B2 (mm) and density in C2 (g/cm³), =PI()*A2^2/4*C2/1000*B2/1000 gives the piece weight in kg.
How do I calculate round bar price from weight?
Find the piece weight first, then multiply by the unit price: piece weight × price per kg, or length (m) × price per metre. Enter the price in the calculator’s optional “Unit price” field and choose its unit to see the amount per piece and in total next to the weight; leave it empty to calculate weight only.