ISO 286 TOLERANCES
n6 tolerance chart
ISO 286 values for the n6 shaft tolerance. Enter a diameter to see the limits; a table for every size band follows below.
Dimension and tolerance
Standard
Feature type
Quick entry by tolerance notation
Examples: 20 h9 · 25 H7/g6
Verified table coverage: 0 < size ≤ 3150 mm; class-specific limits apply. Lists change with dimension. A selected class is not a delivery tolerance commitment.
TOLERANCE CALCULATION
Size limits
Diameter
n6- Minimum size
- 25.015 mm
- Maximum size
- 25.028 mm
- Lower deviation
- +15 µm (+0.015 mm)
- Upper deviation
- +28 µm (+0.028 mm)
- Tolerance width
- 13 µm (0.013 mm)
Check a measured size
This check compares numerical size limits only; it does not assess measurement uncertainty or form tolerances.
The result shows size limits for the selected ISO class. Ovality, straightness, surface roughness and temperature effects are outside this calculation.
n6 tolerance chart
Values from ISO 286-2 for every size band up to 3150 mm, in micrometres (µm). Add the deviations to the nominal size; the calculator above gives the limits in millimetres.
n6 tolerance chartupper / lower deviation, µm · IT: tolerance width, µm
| Size (mm) | n6 shaft | IT6 |
|---|---|---|
| 0–3 | +10 / +4 | 6 |
| 3–6 | +16 / +8 | 8 |
| 6–10 | +19 / +10 | 9 |
| 10–18 | +23 / +12 | 11 |
| 18–30 | +28 / +15 | 13 |
| 30–50 | +33 / +17 | 16 |
| 50–80 | +39 / +20 | 19 |
| 80–120 | +45 / +23 | 22 |
| 120–180 | +52 / +27 | 25 |
| 180–250 | +60 / +31 | 29 |
| 250–315 | +66 / +34 | 32 |
| 315–400 | +73 / +37 | 36 |
| 400–500 | +80 / +40 | 40 |
| 500–630 | +88 / +44 | 44 |
| 630–800 | +100 / +50 | 50 |
| 800–1000 | +112 / +56 | 56 |
| 1000–1250 | +132 / +66 | 66 |
| 1250–1600 | +156 / +78 | 78 |
| 1600–2000 | +184 / +92 | 92 |
| 2000–2500 | +220 / +110 | 110 |
| 2500–3150 | +270 / +135 | 135 |
Worked examples
- Ø10 n6 shaft: in the 6–10 mm band n6 is +19 / +10 µm, so the size must lie between 10.010 and 10.019 mm.
- Ø25 n6 shaft: in the 18–30 mm band n6 is +28 / +15 µm, so the size must lie between 25.015 and 25.028 mm.
- Ø50 n6 shaft: in the 30–50 mm band n6 is +33 / +17 µm, so the size must lie between 50.017 and 50.033 mm.
What does n6 mean?
In an ISO 286 code the letter gives the position of the tolerance zone relative to the nominal size and the number its width (grade IT6). Capital letters are for holes, lower case for shafts.
Both deviations of n6 are positive: the shaft is always slightly above the nominal size, which is why it gives a transition or interference fit with an H hole.
IT6 is usually reached by grinding or precision turning.
Where is n6 used?
n6 gives a tight transition fit with an H7 hole (H7/n6), used where gears, pulleys and hubs are seated on a shaft together with a key.
How to read the n6 tolerance chart
First find the row containing the nominal size: “10–18” covers sizes above 10 mm up to and including 18 mm. Add the upper and lower deviations of that row, in micrometres, to the nominal size; 1000 µm = 1 mm.
The tolerance width is the difference between the upper and lower deviation and equals IT6. Classes ending in the same number (for example H6, h6, js6) share this width; the letter only moves the zone.
Frequently asked questions
What is the n6 tolerance value?
n6: 10–18 mm: +23 / +12 µm; 18–30 mm: +28 / +15 µm; 30–50 mm: +33 / +17 µm. The value grows with size; other bands are in the table.
What are the limits of Ø20 n6?
n6: 20.015 – 20.028 mm (+28 / +15 µm).
Where is n6 used?
n6 gives a tight transition fit with an H7 hole (H7/n6), used where gears, pulleys and hubs are seated on a shaft together with a key.
What does IT6 mean?
IT6 is the ISO 286 tolerance grade and sets the width of the tolerance; it grows with size. At Ø25 mm IT6 = 13 µm. IT6 is usually reached by grinding or precision turning.
How do I calculate a n6 tolerance?
Find the band containing the nominal size and add the upper / lower deviation (µm) to it. Example: Ø20 n6: 20 +28 µm = 20.028 mm and 20 +15 µm = 20.015 mm. The calculator does this for you.