PRECISION IN MATERIAL. CLARITY IN SUPPLY.

ISO 286 TOLERANCES

H8 tolerance chart

ISO 286 values for the H8 and h8 tolerances. Enter a size to see the limits; a table for every size band follows below.

Dimension and tolerance

Standard

Feature type

Tolerance class
ISO H8
Quick entry by tolerance notation

Examples: 20 h9 · 25 H7/g6

Verified table coverage: 0 < size ≤ 3150 mm; class-specific limits apply. Lists change with dimension. A selected class is not a delivery tolerance commitment.

TOLERANCE CALCULATION

Size limits

25 H8 H8: 25 – 25.033 mm (0 / +33 µm)

Diameter

H8
Minimum size
25 mm
Maximum size
25.033 mm
Lower deviation
0 µm (0 mm)
Upper deviation
+33 µm (+0.033 mm)
Tolerance width
33 µm (0.033 mm)
Check a measured size

This check compares numerical size limits only; it does not assess measurement uncertainty or form tolerances.

Tolerance zone µm
Nominal · 0H8033

The result shows size limits for the selected ISO class. Ovality, straightness, surface roughness and temperature effects are outside this calculation.

H8 tolerance chart

Values from ISO 286-2 for every size band up to 3150 mm, in micrometres (µm). Add the deviations to the nominal size; the calculator above gives the limits in millimetres.

H8 tolerance chartupper / lower deviation, µm · IT: tolerance width, µm
Size (mm)H8 holeh8 shaftIT8
0–3+14 / 00 / −1414
3–6+18 / 00 / −1818
6–10+22 / 00 / −2222
10–18+27 / 00 / −2727
18–30+33 / 00 / −3333
30–50+39 / 00 / −3939
50–80+46 / 00 / −4646
80–120+54 / 00 / −5454
120–180+63 / 00 / −6363
180–250+72 / 00 / −7272
250–315+81 / 00 / −8181
315–400+89 / 00 / −8989
400–500+97 / 00 / −9797
500–630+110 / 00 / −110110
630–800+125 / 00 / −125125
800–1000+140 / 00 / −140140
1000–1250+165 / 00 / −165165
1250–1600+195 / 00 / −195195
1600–2000+230 / 00 / −230230
2000–2500+280 / 00 / −280280
2500–3150+330 / 00 / −330330

Worked examples

  1. Ø10 H8 hole: in the 6–10 mm band H8 is +22 / 0 µm, so the size must lie between 10.000 and 10.022 mm.
  2. Ø10 h8 shaft: in the 6–10 mm band h8 is 0 / −22 µm, so the size must lie between 9.978 and 10.000 mm.
  3. Ø25 H8 hole: in the 18–30 mm band H8 is +33 / 0 µm, so the size must lie between 25.000 and 25.033 mm.
  4. Ø25 h8 shaft: in the 18–30 mm band h8 is 0 / −33 µm, so the size must lie between 24.967 and 25.000 mm.

What does H8 mean?

In an ISO 286 code the letter gives the position of the tolerance zone relative to the nominal size and the number its width (grade IT8). Capital letters are for holes, lower case for shafts.

In H8 the lower deviation is zero: the hole can never be smaller than the nominal size, only larger.

In h8 the upper deviation is zero: the shaft can never exceed the nominal size, only be smaller.

IT8 is usually reached by turning, reaming or drawing.

Where is H8 used?

The H8 hole is used in running clearance fits such as H8/f7. h8 appears on drawn or ground bars and on shafts of moderate precision.

How to read the H8 tolerance chart

First find the row containing the nominal size: “10–18” covers sizes above 10 mm up to and including 18 mm. Add the upper and lower deviations of that row, in micrometres, to the nominal size; 1000 µm = 1 mm.

The tolerance width is the difference between the upper and lower deviation and equals IT8. Classes ending in the same number (for example H8, h8, js8) share this width; the letter only moves the zone.

Frequently asked questions

What is the H8 tolerance value?

H8: 10–18 mm: +27 / 0 µm; 18–30 mm: +33 / 0 µm; 30–50 mm: +39 / 0 µm. h8: 10–18 mm: 0 / −27 µm; 18–30 mm: 0 / −33 µm; 30–50 mm: 0 / −39 µm. The value grows with size; other bands are in the table.

What are the limits of Ø20 H8?

H8: 20.000 – 20.033 mm (+33 / 0 µm); h8: 19.967 – 20.000 mm (0 / −33 µm).

What is the difference between H8 and h8?

Capitals are hole tolerances, lower case shaft tolerances. At Ø25 mm H8 is +33 / 0 µm and h8 0 / −33 µm: the same width (IT8) in a different position.

Where is H8 used?

The H8 hole is used in running clearance fits such as H8/f7. h8 appears on drawn or ground bars and on shafts of moderate precision.

What does IT8 mean?

IT8 is the ISO 286 tolerance grade and sets the width of the tolerance; it grows with size. At Ø25 mm IT8 = 33 µm. IT8 is usually reached by turning, reaming or drawing.

How do I calculate a H8 tolerance?

Find the band containing the nominal size and add the upper / lower deviation (µm) to it. Example: Ø20 H8: 20 +33 µm = 20.033 mm and 20 0 µm = 20.000 mm. The calculator does this for you.