ISO 286 TOLERANCES
e8 tolerance chart
ISO 286 values for the e8 shaft tolerance. Enter a diameter to see the limits; a table for every size band follows below.
Dimension and tolerance
Standard
Feature type
Quick entry by tolerance notation
Examples: 20 h9 · 25 H7/g6
Verified table coverage: 0 < size ≤ 3150 mm; class-specific limits apply. Lists change with dimension. A selected class is not a delivery tolerance commitment.
TOLERANCE CALCULATION
Size limits
Diameter
e8- Minimum size
- 24.927 mm
- Maximum size
- 24.96 mm
- Lower deviation
- -73 µm (-0.073 mm)
- Upper deviation
- -40 µm (-0.04 mm)
- Tolerance width
- 33 µm (0.033 mm)
Check a measured size
This check compares numerical size limits only; it does not assess measurement uncertainty or form tolerances.
The result shows size limits for the selected ISO class. Ovality, straightness, surface roughness and temperature effects are outside this calculation.
e8 tolerance chart
Values from ISO 286-2 for every size band up to 3150 mm, in micrometres (µm). Add the deviations to the nominal size; the calculator above gives the limits in millimetres.
e8 tolerance chartupper / lower deviation, µm · IT: tolerance width, µm
| Size (mm) | e8 shaft | IT8 |
|---|---|---|
| 0–3 | −14 / −28 | 14 |
| 3–6 | −20 / −38 | 18 |
| 6–10 | −25 / −47 | 22 |
| 10–18 | −32 / −59 | 27 |
| 18–30 | −40 / −73 | 33 |
| 30–50 | −50 / −89 | 39 |
| 50–80 | −60 / −106 | 46 |
| 80–120 | −72 / −126 | 54 |
| 120–180 | −85 / −148 | 63 |
| 180–250 | −100 / −172 | 72 |
| 250–315 | −110 / −191 | 81 |
| 315–400 | −125 / −214 | 89 |
| 400–500 | −135 / −232 | 97 |
| 500–630 | −145 / −255 | 110 |
| 630–800 | −160 / −285 | 125 |
| 800–1000 | −170 / −310 | 140 |
| 1000–1250 | −195 / −360 | 165 |
| 1250–1600 | −220 / −415 | 195 |
| 1600–2000 | −240 / −470 | 230 |
| 2000–2500 | −260 / −540 | 280 |
| 2500–3150 | −290 / −620 | 330 |
Worked examples
- Ø10 e8 shaft: in the 6–10 mm band e8 is −25 / −47 µm, so the size must lie between 9.953 and 9.975 mm.
- Ø25 e8 shaft: in the 18–30 mm band e8 is −40 / −73 µm, so the size must lie between 24.927 and 24.960 mm.
- Ø50 e8 shaft: in the 30–50 mm band e8 is −50 / −89 µm, so the size must lie between 49.911 and 49.950 mm.
What does e8 mean?
In an ISO 286 code the letter gives the position of the tolerance zone relative to the nominal size and the number its width (grade IT8). Capital letters are for holes, lower case for shafts.
Both deviations of e8 are negative: the shaft is always slightly below the nominal size, which is why it gives a clearance fit with an H hole.
IT8 is usually reached by turning, reaming or drawing.
Where is e8 used?
e8 is used for running fits with generous clearance, on shafts that need extra clearance for temperature differences, long bearings or misalignment.
How to read the e8 tolerance chart
First find the row containing the nominal size: “10–18” covers sizes above 10 mm up to and including 18 mm. Add the upper and lower deviations of that row, in micrometres, to the nominal size; 1000 µm = 1 mm.
The tolerance width is the difference between the upper and lower deviation and equals IT8. Classes ending in the same number (for example H8, h8, js8) share this width; the letter only moves the zone.
Frequently asked questions
What is the e8 tolerance value?
e8: 10–18 mm: −32 / −59 µm; 18–30 mm: −40 / −73 µm; 30–50 mm: −50 / −89 µm. The value grows with size; other bands are in the table.
What are the limits of Ø20 e8?
e8: 19.927 – 19.960 mm (−40 / −73 µm).
Where is e8 used?
e8 is used for running fits with generous clearance, on shafts that need extra clearance for temperature differences, long bearings or misalignment.
What does IT8 mean?
IT8 is the ISO 286 tolerance grade and sets the width of the tolerance; it grows with size. At Ø25 mm IT8 = 33 µm. IT8 is usually reached by turning, reaming or drawing.
How do I calculate a e8 tolerance?
Find the band containing the nominal size and add the upper / lower deviation (µm) to it. Example: Ø20 e8: 20 −40 µm = 19.960 mm and 20 −73 µm = 19.927 mm. The calculator does this for you.