PRECISION IN MATERIAL. CLARITY IN SUPPLY.

ISO 286 TOLERANCES

H6 tolerance chart

ISO 286 values for the H6 and h6 tolerances. Enter a size to see the limits; a table for every size band follows below.

Dimension and tolerance

Standard

Feature type

Tolerance class
ISO h6
Quick entry by tolerance notation

Examples: 20 h9 · 25 H7/g6

Verified table coverage: 0 < size ≤ 3150 mm; class-specific limits apply. Lists change with dimension. A selected class is not a delivery tolerance commitment.

TOLERANCE CALCULATION

Size limits

25 h6 h6: 24.987 – 25 mm (-13 / 0 µm)

Diameter

h6
Minimum size
24.987 mm
Maximum size
25 mm
Lower deviation
-13 µm (-0.013 mm)
Upper deviation
0 µm (0 mm)
Tolerance width
13 µm (0.013 mm)
Check a measured size

This check compares numerical size limits only; it does not assess measurement uncertainty or form tolerances.

Tolerance zone µm
Nominal · 0h6-130

Calculate weight from nominal dimensions

The result shows size limits for the selected ISO class. Ovality, straightness, surface roughness and temperature effects are outside this calculation.

H6 tolerance chart

Values from ISO 286-2 for every size band up to 3150 mm, in micrometres (µm). Add the deviations to the nominal size; the calculator above gives the limits in millimetres.

H6 tolerance chartupper / lower deviation, µm · IT: tolerance width, µm
Size (mm)H6 holeh6 shaftIT6
0–3+6 / 00 / −66
3–6+8 / 00 / −88
6–10+9 / 00 / −99
10–18+11 / 00 / −1111
18–30+13 / 00 / −1313
30–50+16 / 00 / −1616
50–80+19 / 00 / −1919
80–120+22 / 00 / −2222
120–180+25 / 00 / −2525
180–250+29 / 00 / −2929
250–315+32 / 00 / −3232
315–400+36 / 00 / −3636
400–500+40 / 00 / −4040
500–630+44 / 00 / −4444
630–800+50 / 00 / −5050
800–1000+56 / 00 / −5656
1000–1250+66 / 00 / −6666
1250–1600+78 / 00 / −7878
1600–2000+92 / 00 / −9292
2000–2500+110 / 00 / −110110
2500–3150+135 / 00 / −135135

Worked examples

  1. Ø10 H6 hole: in the 6–10 mm band H6 is +9 / 0 µm, so the size must lie between 10.000 and 10.009 mm.
  2. Ø10 h6 shaft: in the 6–10 mm band h6 is 0 / −9 µm, so the size must lie between 9.991 and 10.000 mm.
  3. Ø25 H6 hole: in the 18–30 mm band H6 is +13 / 0 µm, so the size must lie between 25.000 and 25.013 mm.
  4. Ø25 h6 shaft: in the 18–30 mm band h6 is 0 / −13 µm, so the size must lie between 24.987 and 25.000 mm.

What does H6 mean?

In an ISO 286 code the letter gives the position of the tolerance zone relative to the nominal size and the number its width (grade IT6). Capital letters are for holes, lower case for shafts.

In H6 the lower deviation is zero: the hole can never be smaller than the nominal size, only larger.

In h6 the upper deviation is zero: the shaft can never exceed the nominal size, only be smaller.

IT6 is usually reached by grinding or precision turning.

Where is H6 used?

h6 is common on ground shafts, precision pins and bushes, and is the shaft side of the H7/h6 locational clearance fit. The H6 hole is used where an even closer location is needed.

How to read the H6 tolerance chart

First find the row containing the nominal size: “10–18” covers sizes above 10 mm up to and including 18 mm. Add the upper and lower deviations of that row, in micrometres, to the nominal size; 1000 µm = 1 mm.

The tolerance width is the difference between the upper and lower deviation and equals IT6. Classes ending in the same number (for example H6, h6, js6) share this width; the letter only moves the zone.

Frequently asked questions

What is the H6 tolerance value?

H6: 10–18 mm: +11 / 0 µm; 18–30 mm: +13 / 0 µm; 30–50 mm: +16 / 0 µm. h6: 10–18 mm: 0 / −11 µm; 18–30 mm: 0 / −13 µm; 30–50 mm: 0 / −16 µm. The value grows with size; other bands are in the table.

What are the limits of Ø20 H6?

H6: 20.000 – 20.013 mm (+13 / 0 µm); h6: 19.987 – 20.000 mm (0 / −13 µm).

What is the difference between H6 and h6?

Capitals are hole tolerances, lower case shaft tolerances. At Ø25 mm H6 is +13 / 0 µm and h6 0 / −13 µm: the same width (IT6) in a different position.

Where is H6 used?

h6 is common on ground shafts, precision pins and bushes, and is the shaft side of the H7/h6 locational clearance fit. The H6 hole is used where an even closer location is needed.

What does IT6 mean?

IT6 is the ISO 286 tolerance grade and sets the width of the tolerance; it grows with size. At Ø25 mm IT6 = 13 µm. IT6 is usually reached by grinding or precision turning.

How do I calculate a H6 tolerance?

Find the band containing the nominal size and add the upper / lower deviation (µm) to it. Example: Ø20 H6: 20 +13 µm = 20.013 mm and 20 0 µm = 20.000 mm. The calculator does this for you.