ISO 286 TOLERANCES
d9 tolerance chart
ISO 286 values for the d9 shaft tolerance. Enter a diameter to see the limits; a table for every size band follows below.
Dimension and tolerance
Standard
Feature type
Quick entry by tolerance notation
Examples: 20 h9 · 25 H7/g6
Verified table coverage: 0 < size ≤ 3150 mm; class-specific limits apply. Lists change with dimension. A selected class is not a delivery tolerance commitment.
TOLERANCE CALCULATION
Size limits
Diameter
d9- Minimum size
- 24.883 mm
- Maximum size
- 24.935 mm
- Lower deviation
- -117 µm (-0.117 mm)
- Upper deviation
- -65 µm (-0.065 mm)
- Tolerance width
- 52 µm (0.052 mm)
Check a measured size
This check compares numerical size limits only; it does not assess measurement uncertainty or form tolerances.
The result shows size limits for the selected ISO class. Ovality, straightness, surface roughness and temperature effects are outside this calculation.
d9 tolerance chart
Values from ISO 286-2 for every size band up to 3150 mm, in micrometres (µm). Add the deviations to the nominal size; the calculator above gives the limits in millimetres.
d9 tolerance chartupper / lower deviation, µm · IT: tolerance width, µm
| Size (mm) | d9 shaft | IT9 |
|---|---|---|
| 0–3 | −20 / −45 | 25 |
| 3–6 | −30 / −60 | 30 |
| 6–10 | −40 / −76 | 36 |
| 10–18 | −50 / −93 | 43 |
| 18–30 | −65 / −117 | 52 |
| 30–50 | −80 / −142 | 62 |
| 50–80 | −100 / −174 | 74 |
| 80–120 | −120 / −207 | 87 |
| 120–180 | −145 / −245 | 100 |
| 180–250 | −170 / −285 | 115 |
| 250–315 | −190 / −320 | 130 |
| 315–400 | −210 / −350 | 140 |
| 400–500 | −230 / −385 | 155 |
| 500–630 | −260 / −435 | 175 |
| 630–800 | −290 / −490 | 200 |
| 800–1000 | −320 / −550 | 230 |
| 1000–1250 | −350 / −610 | 260 |
| 1250–1600 | −390 / −700 | 310 |
| 1600–2000 | −430 / −800 | 370 |
| 2000–2500 | −480 / −920 | 440 |
| 2500–3150 | −520 / −1060 | 540 |
Worked examples
- Ø10 d9 shaft: in the 6–10 mm band d9 is −40 / −76 µm, so the size must lie between 9.924 and 9.960 mm.
- Ø25 d9 shaft: in the 18–30 mm band d9 is −65 / −117 µm, so the size must lie between 24.883 and 24.935 mm.
- Ø50 d9 shaft: in the 30–50 mm band d9 is −80 / −142 µm, so the size must lie between 49.858 and 49.920 mm.
What does d9 mean?
In an ISO 286 code the letter gives the position of the tolerance zone relative to the nominal size and the number its width (grade IT9). Capital letters are for holes, lower case for shafts.
Both deviations of d9 are negative: the shaft is always slightly below the nominal size, which is why it gives a clearance fit with an H hole.
IT9 is usually reached by turning or cold drawing.
Where is d9 used?
d9 forms the H9/d9 free-running fit, used in bearings where free movement matters more than precision and large temperature changes occur.
How to read the d9 tolerance chart
First find the row containing the nominal size: “10–18” covers sizes above 10 mm up to and including 18 mm. Add the upper and lower deviations of that row, in micrometres, to the nominal size; 1000 µm = 1 mm.
The tolerance width is the difference between the upper and lower deviation and equals IT9. Classes ending in the same number (for example H9, h9, js9) share this width; the letter only moves the zone.
Frequently asked questions
What is the d9 tolerance value?
d9: 10–18 mm: −50 / −93 µm; 18–30 mm: −65 / −117 µm; 30–50 mm: −80 / −142 µm. The value grows with size; other bands are in the table.
What are the limits of Ø20 d9?
d9: 19.883 – 19.935 mm (−65 / −117 µm).
Where is d9 used?
d9 forms the H9/d9 free-running fit, used in bearings where free movement matters more than precision and large temperature changes occur.
What does IT9 mean?
IT9 is the ISO 286 tolerance grade and sets the width of the tolerance; it grows with size. At Ø25 mm IT9 = 52 µm. IT9 is usually reached by turning or cold drawing.
How do I calculate a d9 tolerance?
Find the band containing the nominal size and add the upper / lower deviation (µm) to it. Example: Ø20 d9: 20 −65 µm = 19.935 mm and 20 −117 µm = 19.883 mm. The calculator does this for you.