ISO 286 TOLERANCES
H8/f7 fit
Hole and shaft limits and the clearance or interference of an H8/f7 fit. Enter a size; a table for every size band follows below.
Dimension and tolerance
Hole and shaft use the same nominal dimension.
Quick entry by tolerance notation
Examples: 20 h9 · 25 H7/g6
Verified table coverage: 0 < size ≤ 3150 mm; class-specific limits apply. Lists change with dimension. A selected class is not a delivery tolerance commitment.
TOLERANCE CALCULATION
Size limits
Clearance fit
Clearance is between +20 and +74 µm.
Hole
H8- Minimum size
- 25 mm
- Maximum size
- 25.033 mm
- Lower deviation
- 0 µm (0 mm)
- Upper deviation
- +33 µm (+0.033 mm)
- Tolerance width
- 33 µm (0.033 mm)
Shaft
f7- Minimum size
- 24.959 mm
- Maximum size
- 24.98 mm
- Lower deviation
- -41 µm (-0.041 mm)
- Upper deviation
- -20 µm (-0.02 mm)
- Tolerance width
- 21 µm (0.021 mm)
The result shows size limits for the selected ISO class. Ovality, straightness, surface roughness and temperature effects are outside this calculation.
H8/f7 fit
Values from ISO 286-2 for every size band up to 3150 mm, in micrometres (µm). Add the deviations to the nominal size; the calculator above gives the limits in millimetres.
H8/f7 fit tablehole and shaft: upper / lower deviation, µm · clearance: min … max, µm (negative = interference)
| Size (mm) | H8 hole | f7 shaft | Clearance | Type |
|---|---|---|---|---|
| 0–3 | +14 / 0 | −6 / −16 | +6 … +30 | Clearance |
| 3–6 | +18 / 0 | −10 / −22 | +10 … +40 | Clearance |
| 6–10 | +22 / 0 | −13 / −28 | +13 … +50 | Clearance |
| 10–18 | +27 / 0 | −16 / −34 | +16 … +61 | Clearance |
| 18–30 | +33 / 0 | −20 / −41 | +20 … +74 | Clearance |
| 30–50 | +39 / 0 | −25 / −50 | +25 … +89 | Clearance |
| 50–80 | +46 / 0 | −30 / −60 | +30 … +106 | Clearance |
| 80–120 | +54 / 0 | −36 / −71 | +36 … +125 | Clearance |
| 120–180 | +63 / 0 | −43 / −83 | +43 … +146 | Clearance |
| 180–250 | +72 / 0 | −50 / −96 | +50 … +168 | Clearance |
| 250–315 | +81 / 0 | −56 / −108 | +56 … +189 | Clearance |
| 315–400 | +89 / 0 | −62 / −119 | +62 … +208 | Clearance |
| 400–500 | +97 / 0 | −68 / −131 | +68 … +228 | Clearance |
| 500–630 | +110 / 0 | −76 / −146 | +76 … +256 | Clearance |
| 630–800 | +125 / 0 | −80 / −160 | +80 … +285 | Clearance |
| 800–1000 | +140 / 0 | −86 / −176 | +86 … +316 | Clearance |
| 1000–1250 | +165 / 0 | −98 / −203 | +98 … +368 | Clearance |
| 1250–1600 | +195 / 0 | −110 / −235 | +110 … +430 | Clearance |
| 1600–2000 | +230 / 0 | −120 / −270 | +120 … +500 | Clearance |
| 2000–2500 | +280 / 0 | −130 / −305 | +130 … +585 | Clearance |
| 2500–3150 | +330 / 0 | −145 / −355 | +145 … +685 | Clearance |
Worked examples
- Ø20 H8/f7: hole 20.000–20.033 mm, shaft 19.959–19.980 mm. Clearance from +20 to +74 µm: a clearance fit.
- Ø50 H8/f7: hole 50.000–50.039 mm, shaft 49.950–49.975 mm. Clearance from +25 to +89 µm: a clearance fit.
What does an H8/f7 fit mean?
H8/f7 pairs a hole toleranced H8 with a shaft toleranced f7. At Ø25 mm the hole is +33 / 0 µm and the shaft −20 / −41 µm; clearance stays between +20 and +74 µm. It is a clearance fit.
A negative clearance means interference: the shaft is larger than the hole. The values change with the size band; use the row whose band contains the nominal size.
Where is H8/f7 used?
Close running fit: the classic fit for turning shafts and precise sliding parts in machines; the hole tolerance is wider than in H7/f7.
In a clearance fit parts assemble by hand; lubrication and cleanliness are enough.
Frequently asked questions
Is H8/f7 a clearance or interference fit?
H8/f7 is a clearance fit. At Ø25 mm clearance runs from +20 to +74 µm.
What is the clearance of a Ø50 H8/f7 fit?
At Ø50 mm the hole is 50.000–50.039 mm and the shaft 49.950–49.975 mm. Clearance runs from +25 to +89 µm (negative means interference).
Where is an H8/f7 fit used?
Close running fit: the classic fit for turning shafts and precise sliding parts in machines; the hole tolerance is wider than in H7/f7.
What is the difference between H8/f7 and H7/f7?
At Ø25 mm H8/f7 gives +20 … +74 µm and H7/f7 +20 … +62 µm. Both are clearance fits; H7/f7 is the tighter one.
How is an H8/f7 fit calculated?
Find the hole and shaft limits for the same nominal size in the ISO 286 table. Minimum clearance = lowest hole − largest shaft; maximum clearance = largest hole − smallest shaft. Both positive means clearance, both negative interference, mixed signs a transition fit.