ISO 286 TOLERANCES
H7/k6 fit
Hole and shaft limits and the clearance or interference of an H7/k6 fit. Enter a size; a table for every size band follows below.
Dimension and tolerance
Hole and shaft use the same nominal dimension.
Quick entry by tolerance notation
Examples: 20 h9 · 25 H7/g6
Verified table coverage: 0 < size ≤ 3150 mm; class-specific limits apply. Lists change with dimension. A selected class is not a delivery tolerance commitment.
TOLERANCE CALCULATION
Size limits
Transition fit
The hole-minus-shaft size difference is between -15 and +19 µm.
Actual sizes can produce either clearance or interference.
Hole
H7- Minimum size
- 25 mm
- Maximum size
- 25.021 mm
- Lower deviation
- 0 µm (0 mm)
- Upper deviation
- +21 µm (+0.021 mm)
- Tolerance width
- 21 µm (0.021 mm)
Shaft
k6- Minimum size
- 25.002 mm
- Maximum size
- 25.015 mm
- Lower deviation
- +2 µm (+0.002 mm)
- Upper deviation
- +15 µm (+0.015 mm)
- Tolerance width
- 13 µm (0.013 mm)
The result shows size limits for the selected ISO class. Ovality, straightness, surface roughness and temperature effects are outside this calculation.
H7/k6 fit
Values from ISO 286-2 for every size band up to 3150 mm, in micrometres (µm). Add the deviations to the nominal size; the calculator above gives the limits in millimetres.
H7/k6 fit tablehole and shaft: upper / lower deviation, µm · clearance: min … max, µm (negative = interference)
| Size (mm) | H7 hole | k6 shaft | Clearance | Type |
|---|---|---|---|---|
| 0–3 | +10 / 0 | +6 / 0 | −6 … +10 | Transition |
| 3–6 | +12 / 0 | +9 / +1 | −9 … +11 | Transition |
| 6–10 | +15 / 0 | +10 / +1 | −10 … +14 | Transition |
| 10–18 | +18 / 0 | +12 / +1 | −12 … +17 | Transition |
| 18–30 | +21 / 0 | +15 / +2 | −15 … +19 | Transition |
| 30–50 | +25 / 0 | +18 / +2 | −18 … +23 | Transition |
| 50–80 | +30 / 0 | +21 / +2 | −21 … +28 | Transition |
| 80–120 | +35 / 0 | +25 / +3 | −25 … +32 | Transition |
| 120–180 | +40 / 0 | +28 / +3 | −28 … +37 | Transition |
| 180–250 | +46 / 0 | +33 / +4 | −33 … +42 | Transition |
| 250–315 | +52 / 0 | +36 / +4 | −36 … +48 | Transition |
| 315–400 | +57 / 0 | +40 / +4 | −40 … +53 | Transition |
| 400–500 | +63 / 0 | +45 / +5 | −45 … +58 | Transition |
| 500–630 | +70 / 0 | +44 / 0 | −44 … +70 | Transition |
| 630–800 | +80 / 0 | +50 / 0 | −50 … +80 | Transition |
| 800–1000 | +90 / 0 | +56 / 0 | −56 … +90 | Transition |
| 1000–1250 | +105 / 0 | +66 / 0 | −66 … +105 | Transition |
| 1250–1600 | +125 / 0 | +78 / 0 | −78 … +125 | Transition |
| 1600–2000 | +150 / 0 | +92 / 0 | −92 … +150 | Transition |
| 2000–2500 | +175 / 0 | +110 / 0 | −110 … +175 | Transition |
| 2500–3150 | +210 / 0 | +135 / 0 | −135 … +210 | Transition |
Worked examples
- Ø20 H7/k6: hole 20.000–20.021 mm, shaft 20.002–20.015 mm. Clearance from −15 to +19 µm: a transition fit.
- Ø50 H7/k6: hole 50.000–50.025 mm, shaft 50.002–50.018 mm. Clearance from −18 to +23 µm: a transition fit.
What does an H7/k6 fit mean?
H7/k6 pairs a hole toleranced H7 with a shaft toleranced k6. At Ø25 mm the hole is +21 / 0 µm and the shaft +15 / +2 µm; clearance stays between −15 and +19 µm. It is a transition fit.
A negative clearance means interference: the shaft is larger than the hole. The values change with the size band; use the row whose band contains the nominal size.
Where is H7/k6 used?
Locational transition fit: depending on actual sizes there is a small clearance or interference. Used for gears, pulleys and bearing seats fitted with light pressure or a mallet.
Transition fits are usually assembled with a mallet or light press; the actual sizes decide whether clearance or interference results.
Frequently asked questions
Is H7/k6 a clearance or interference fit?
H7/k6 is a transition fit. At Ø25 mm clearance runs from −15 to +19 µm; actual sizes can give either a small clearance or interference.
What is the clearance of a Ø50 H7/k6 fit?
At Ø50 mm the hole is 50.000–50.025 mm and the shaft 50.002–50.018 mm. Clearance runs from −18 to +23 µm (negative means interference).
Where is an H7/k6 fit used?
Locational transition fit: depending on actual sizes there is a small clearance or interference. Used for gears, pulleys and bearing seats fitted with light pressure or a mallet.
What is the difference between H7/k6 and H7/n6?
At Ø25 mm H7/k6 gives −15 … +19 µm and H7/n6 −28 … +6 µm. Both are transition fits; H7/n6 is the tighter one.
How is an H7/k6 fit calculated?
Find the hole and shaft limits for the same nominal size in the ISO 286 table. Minimum clearance = lowest hole − largest shaft; maximum clearance = largest hole − smallest shaft. Both positive means clearance, both negative interference, mixed signs a transition fit.