ISO 286 TOLERANCES
H7/n6 fit
Hole and shaft limits and the clearance or interference of an H7/n6 fit. Enter a size; a table for every size band follows below.
Dimension and tolerance
Hole and shaft use the same nominal dimension.
Quick entry by tolerance notation
Examples: 20 h9 · 25 H7/g6
Verified table coverage: 0 < size ≤ 3150 mm; class-specific limits apply. Lists change with dimension. A selected class is not a delivery tolerance commitment.
TOLERANCE CALCULATION
Size limits
Transition fit
The hole-minus-shaft size difference is between -28 and +6 µm.
Actual sizes can produce either clearance or interference.
Hole
H7- Minimum size
- 25 mm
- Maximum size
- 25.021 mm
- Lower deviation
- 0 µm (0 mm)
- Upper deviation
- +21 µm (+0.021 mm)
- Tolerance width
- 21 µm (0.021 mm)
Shaft
n6- Minimum size
- 25.015 mm
- Maximum size
- 25.028 mm
- Lower deviation
- +15 µm (+0.015 mm)
- Upper deviation
- +28 µm (+0.028 mm)
- Tolerance width
- 13 µm (0.013 mm)
The result shows size limits for the selected ISO class. Ovality, straightness, surface roughness and temperature effects are outside this calculation.
H7/n6 fit
Values from ISO 286-2 for every size band up to 3150 mm, in micrometres (µm). Add the deviations to the nominal size; the calculator above gives the limits in millimetres.
H7/n6 fit tablehole and shaft: upper / lower deviation, µm · clearance: min … max, µm (negative = interference)
| Size (mm) | H7 hole | n6 shaft | Clearance | Type |
|---|---|---|---|---|
| 0–3 | +10 / 0 | +10 / +4 | −10 … +6 | Transition |
| 3–6 | +12 / 0 | +16 / +8 | −16 … +4 | Transition |
| 6–10 | +15 / 0 | +19 / +10 | −19 … +5 | Transition |
| 10–18 | +18 / 0 | +23 / +12 | −23 … +6 | Transition |
| 18–30 | +21 / 0 | +28 / +15 | −28 … +6 | Transition |
| 30–50 | +25 / 0 | +33 / +17 | −33 … +8 | Transition |
| 50–80 | +30 / 0 | +39 / +20 | −39 … +10 | Transition |
| 80–120 | +35 / 0 | +45 / +23 | −45 … +12 | Transition |
| 120–180 | +40 / 0 | +52 / +27 | −52 … +13 | Transition |
| 180–250 | +46 / 0 | +60 / +31 | −60 … +15 | Transition |
| 250–315 | +52 / 0 | +66 / +34 | −66 … +18 | Transition |
| 315–400 | +57 / 0 | +73 / +37 | −73 … +20 | Transition |
| 400–500 | +63 / 0 | +80 / +40 | −80 … +23 | Transition |
| 500–630 | +70 / 0 | +88 / +44 | −88 … +26 | Transition |
| 630–800 | +80 / 0 | +100 / +50 | −100 … +30 | Transition |
| 800–1000 | +90 / 0 | +112 / +56 | −112 … +34 | Transition |
| 1000–1250 | +105 / 0 | +132 / +66 | −132 … +39 | Transition |
| 1250–1600 | +125 / 0 | +156 / +78 | −156 … +47 | Transition |
| 1600–2000 | +150 / 0 | +184 / +92 | −184 … +58 | Transition |
| 2000–2500 | +175 / 0 | +220 / +110 | −220 … +65 | Transition |
| 2500–3150 | +210 / 0 | +270 / +135 | −270 … +75 | Transition |
Worked examples
- Ø20 H7/n6: hole 20.000–20.021 mm, shaft 20.015–20.028 mm. Clearance from −28 to +6 µm: a transition fit.
- Ø50 H7/n6: hole 50.000–50.025 mm, shaft 50.017–50.033 mm. Clearance from −33 to +8 µm: a transition fit.
What does an H7/n6 fit mean?
H7/n6 pairs a hole toleranced H7 with a shaft toleranced n6. At Ø25 mm the hole is +21 / 0 µm and the shaft +28 / +15 µm; clearance stays between −28 and +6 µm. It is a transition fit.
A negative clearance means interference: the shaft is larger than the hole. The values change with the size band; use the row whose band contains the nominal size.
Where is H7/n6 used?
Tight transition fit: in most cases it produces interference. Used for hubs, gears and couplings seated with a key; assembly needs a press.
Transition fits are usually assembled with a mallet or light press; the actual sizes decide whether clearance or interference results.
Frequently asked questions
Is H7/n6 a clearance or interference fit?
H7/n6 is a transition fit. At Ø25 mm clearance runs from −28 to +6 µm; actual sizes can give either a small clearance or interference.
What is the clearance of a Ø50 H7/n6 fit?
At Ø50 mm the hole is 50.000–50.025 mm and the shaft 50.017–50.033 mm. Clearance runs from −33 to +8 µm (negative means interference).
Where is an H7/n6 fit used?
Tight transition fit: in most cases it produces interference. Used for hubs, gears and couplings seated with a key; assembly needs a press.
What is the difference between H7/n6 and H7/p6?
At Ø25 mm H7/n6 gives −28 … +6 µm and H7/p6 −35 … −1 µm. H7/n6 is a transition fit, H7/p6 a interference fit.
How is an H7/n6 fit calculated?
Find the hole and shaft limits for the same nominal size in the ISO 286 table. Minimum clearance = lowest hole − largest shaft; maximum clearance = largest hole − smallest shaft. Both positive means clearance, both negative interference, mixed signs a transition fit.