ISO 286 TOLERANCES
H7/js6 fit
Hole and shaft limits and the clearance or interference of an H7/js6 fit. Enter a size; a table for every size band follows below.
Dimension and tolerance
Hole and shaft use the same nominal dimension.
Quick entry by tolerance notation
Examples: 20 h9 · 25 H7/g6
Verified table coverage: 0 < size ≤ 3150 mm; class-specific limits apply. Lists change with dimension. A selected class is not a delivery tolerance commitment.
TOLERANCE CALCULATION
Size limits
Transition fit
The hole-minus-shaft size difference is between -6.5 and +27.5 µm.
Actual sizes can produce either clearance or interference.
Hole
H7- Minimum size
- 25 mm
- Maximum size
- 25.021 mm
- Lower deviation
- 0 µm (0 mm)
- Upper deviation
- +21 µm (+0.021 mm)
- Tolerance width
- 21 µm (0.021 mm)
Shaft
js6- Minimum size
- 24.9935 mm
- Maximum size
- 25.0065 mm
- Lower deviation
- -6.5 µm (-0.0065 mm)
- Upper deviation
- +6.5 µm (+0.0065 mm)
- Tolerance width
- 13 µm (0.013 mm)
The result shows size limits for the selected ISO class. Ovality, straightness, surface roughness and temperature effects are outside this calculation.
H7/js6 fit
Values from ISO 286-2 for every size band up to 3150 mm, in micrometres (µm). Add the deviations to the nominal size; the calculator above gives the limits in millimetres.
H7/js6 fit tablehole and shaft: upper / lower deviation, µm · clearance: min … max, µm (negative = interference)
| Size (mm) | H7 hole | js6 shaft | Clearance | Type |
|---|---|---|---|---|
| 0–3 | +10 / 0 | +3 / −3 | −3 … +13 | Transition |
| 3–6 | +12 / 0 | +4 / −4 | −4 … +16 | Transition |
| 6–10 | +15 / 0 | +4.5 / −4.5 | −4.5 … +19.5 | Transition |
| 10–18 | +18 / 0 | +5.5 / −5.5 | −5.5 … +23.5 | Transition |
| 18–30 | +21 / 0 | +6.5 / −6.5 | −6.5 … +27.5 | Transition |
| 30–50 | +25 / 0 | +8 / −8 | −8 … +33 | Transition |
| 50–80 | +30 / 0 | +9.5 / −9.5 | −9.5 … +39.5 | Transition |
| 80–120 | +35 / 0 | +11 / −11 | −11 … +46 | Transition |
| 120–180 | +40 / 0 | +12.5 / −12.5 | −12.5 … +52.5 | Transition |
| 180–250 | +46 / 0 | +14.5 / −14.5 | −14.5 … +60.5 | Transition |
| 250–315 | +52 / 0 | +16 / −16 | −16 … +68 | Transition |
| 315–400 | +57 / 0 | +18 / −18 | −18 … +75 | Transition |
| 400–500 | +63 / 0 | +20 / −20 | −20 … +83 | Transition |
| 500–630 | +70 / 0 | +22 / −22 | −22 … +92 | Transition |
| 630–800 | +80 / 0 | +25 / −25 | −25 … +105 | Transition |
| 800–1000 | +90 / 0 | +28 / −28 | −28 … +118 | Transition |
| 1000–1250 | +105 / 0 | +33 / −33 | −33 … +138 | Transition |
| 1250–1600 | +125 / 0 | +39 / −39 | −39 … +164 | Transition |
| 1600–2000 | +150 / 0 | +46 / −46 | −46 … +196 | Transition |
| 2000–2500 | +175 / 0 | +55 / −55 | −55 … +230 | Transition |
| 2500–3150 | +210 / 0 | +67.5 / −67.5 | −67.5 … +277.5 | Transition |
Worked examples
- Ø20 H7/js6: hole 20.000–20.021 mm, shaft 19.994–20.007 mm. Clearance from −6.5 to +27.5 µm: a transition fit.
- Ø50 H7/js6: hole 50.000–50.025 mm, shaft 49.992–50.008 mm. Clearance from −8 to +33 µm: a transition fit.
What does an H7/js6 fit mean?
H7/js6 pairs a hole toleranced H7 with a shaft toleranced js6. At Ø25 mm the hole is +21 / 0 µm and the shaft +6.5 / −6.5 µm; clearance stays between −6.5 and +27.5 µm. It is a transition fit.
A negative clearance means interference: the shaft is larger than the hole. The values change with the size band; use the row whose band contains the nominal size.
Where is H7/js6 used?
Symmetric transition fit: the shaft tolerance is split evenly about the nominal size, giving small clearance or interference. Used for accurately located parts fitted by hand or with a mallet.
Transition fits are usually assembled with a mallet or light press; the actual sizes decide whether clearance or interference results.
Frequently asked questions
Is H7/js6 a clearance or interference fit?
H7/js6 is a transition fit. At Ø25 mm clearance runs from −6.5 to +27.5 µm; actual sizes can give either a small clearance or interference.
What is the clearance of a Ø50 H7/js6 fit?
At Ø50 mm the hole is 50.000–50.025 mm and the shaft 49.992–50.008 mm. Clearance runs from −8 to +33 µm (negative means interference).
Where is an H7/js6 fit used?
Symmetric transition fit: the shaft tolerance is split evenly about the nominal size, giving small clearance or interference. Used for accurately located parts fitted by hand or with a mallet.
What is the difference between H7/js6 and H7/k6?
At Ø25 mm H7/js6 gives −6.5 … +27.5 µm and H7/k6 −15 … +19 µm. Both are transition fits; H7/k6 is the tighter one.
How is an H7/js6 fit calculated?
Find the hole and shaft limits for the same nominal size in the ISO 286 table. Minimum clearance = lowest hole − largest shaft; maximum clearance = largest hole − smallest shaft. Both positive means clearance, both negative interference, mixed signs a transition fit.