PRECISION IN MATERIAL. CLARITY IN SUPPLY.

ALUMINIUM 2XXX

3.1355 (EN AW-2024) Aluminium

3.1355 (EN AW-2024) is a copper-magnesium aluminium alloy for machine and aerospace parts needing high strength and good machinability. Its low corrosion resistance makes surface protection important. This page covers the 3.1355 material properties: chemical composition, mechanical values, applications and supply forms.

Calculate weight with this grade
Grade / Alloy
EN AW-2024
EN / W.Nr.
3.1355AlCu4Mg1
AISI / SAE
—
UNS
A92024
Other names
AlCuMg2
Family
Aluminium 2xxx
Density
2.77 g/cm³

3.1355 (EN AW-2024) chemical composition

Chemical composition

Composition limits

EN 573-3-based composition limits (IBL 2024 product sheet, 12/2025). Other elements: each maximum 0.05%, total maximum 0.15%. The Ti limit is taken from Delta-Trading's 3.1355 page.

EN AW-2024 — chemical composition, % by mass
ElementContent (% by mass)
SiSilicon≤ 0.5
FeIron≤ 0.5
CuCopper3.8–4.9
MnManganese0.3–0.9
MgMagnesium1.2–1.8
CrChromium≤ 0.1
ZnZinc≤ 0.25
TiTitanium≤ 0.15
AlAluminiumBalance

Values describe the grade, not the analysis of a specific batch. The applicable product specification and material certificate determine acceptance.

EN AW-2024 / 3.1355 supply options

EN AW-2024 / 3.1355 — product forms and dimensions
Product formDimensions / options
Round barDiameter and length options
Flat barThickness × width × length
Solid square barSide dimension and length
Hexagonal barWidth across flats and length
Sheet and plateThickness × width × length
StripThickness and strip width; coil or cut-length options
Tube / pipeOutside diameter × wall thickness × length
Cut-to-size blanksCut lengths or blanks from the listed product forms

Condition optionsT3, T3510 and T3511; other tempers depending on product formDelivery and heat-treatment conditions

Dimensions, delivery condition and lead time are assessed for each enquiry.

What aluminium alloy is 3.1355?

3.1355 is the material number of the aluminium-copper-magnesium alloy known as EN AW-2024. Its EN 573-3 chemical designation is AlCu4Mg1, the former DIN name is AlCuMg2 and the UNS code is A92024. This 2xxx-series alloy is strengthened by heat treatment: solution treatment holds the metal at high temperature and cools it quickly, and very small copper- and magnesium-bearing particles then form during a holding period that raises strength. This holding period is called ageing.

T3/T3511 values for extruded round bar

The values below are minimum values for extruded round bar to EN 755-2 and decrease as the diameter increases. T3 is solution treated, cold worked and naturally aged at room temperature. In T3511, residual stress is reduced by stretching, and minor straightening may follow the stretching.

DiameterRm, min. (MPa)Rp0.2, min. (MPa)A50mm, min. (%)
≤ 50 mm4503106
50–100 mm4403006
100–200 mm4202806
200–250 mm4002706
Sources and technical details

Source: IBL Metallhandel, 2024 round bar product sheet, 12/2025; EN 755-2 values. Elongation is given as a single value for all diameters. Values for larger sections are agreed separately.

Rm is tensile strength, Rp0.2 the proof strength at 0.2% permanent extension and A50mm the elongation after fracture over a 50 mm gauge length.

Sheet and plate (EN 485-2), drawn bar and tube (EN 754-2) and other tempers such as O, T4, T351 or T8 have separately defined values depending on product form and thickness; this table should not be used in their place.

IBL Metallhandel — 2024 round bar product sheet, 12/2025 (PDF) — EN 573-3 composition and EN 755-2 mechanical values; extruded round bar, T3/T3511.

Applications and limitations

EN AW-2024 is used in machine building, pneumatic and hydraulic housings, fixtures, drive systems and aerospace structural parts because of its high strength and good machinability. Its corrosion resistance is low, so parts are usually protected by anodising or coating. It is not suitable for fusion welding; joints are generally made mechanically or by resistance welding.

How it relates to 2017A and 7075

2017A and 2024 belong to the same Al-Cu-Mg family; 2024 has a higher magnesium range (1.2–1.8%) than 2017A (0.4–1.0%). According to Kaiser Aluminum's 7075 rod and bar sheet, the T73/T7351 tempers of 7075 can replace 2024, 2014 and 2017 in many critical applications because of their stress-corrosion resistance. The choice depends on load, environment and fabrication route.

Typical application areas

Machine parts, pneumatic and hydraulic housings, fixtures, aerospace structural parts.

Product and cutting options

Relevant product forms for this material are listed below. Availability varies with grade and dimensions.