PRECISION IN MATERIAL. CLARITY IN SUPPLY.

ALLOY STEEL

1.7035 (41Cr4) Alloy Steel

41Cr4 (1.7035) is a chromium-alloyed quenched-and-tempered steel. After hardening and tempering it is used for drive components such as crankshafts, axles, steering knuckles and steering parts. It suits parts needing less strength than 42CrMo4 and responds to induction surface hardening. This page covers the 1.7035 material properties: chemical composition, mechanical values and applications.

Grade / Alloy
41Cr4
EN / W.Nr.
1.703541Cr4
AISI / SAE
5140
UNS
—
Other names
41CrS4 (1.7039) · JIS SCr440
Family
Alloy steel
Density
7.8 g/cm³

1.7035 (41Cr4) chemical composition

Chemical composition

Composition limits

EN 10083-3 cast analysis limits for 41Cr4 (Ovako and EN tables); 41CrS4 has 0.020–0.035 sulphur.

41Cr4 — chemical composition, % by mass
ElementContent (% by mass)
CCarbon0.38–0.45
SiSilicon≤ 0.4
MnManganese0.6–0.9
PPhosphorus≤ 0.025
SSulfur≤ 0.035
CrChromium0.9–1.2

Values describe the grade, not the analysis of a specific batch. The applicable product specification and material certificate determine acceptance.

41Cr4 in drive components

41Cr4 is a chromium-alloyed quenched-and-tempered steel: it is hardened and then reheated in a controlled way (tempering). The producer data sheet recommends it, at a tensile strength of 800–1100 MPa in this condition, for drive components such as crankshafts, front axles, steering knuckles and steering parts.

Without molybdenum it does not harden as deeply as 42CrMo4 (4140); Ovako states that it through-hardens in oil up to about 40 mm diameter. It is therefore used for parts of moderate section needing less strength than 42CrMo4. Its surface can be induction hardened to at least 52 HRC.

41Cr4 mechanical properties (quenched and tempered, +QT)

The strength of quenched-and-tempered 41Cr4 falls as the section grows, because the core of a thick part does not cool as quickly. The table gives the EN 10083-3 minimum values by diameter range; no values are given above 100 mm.

Diameter d (mm)Rp0.2 min (MPa)Rm (MPa)A min (%)Z min (%)
≤ 168001000–12001130
16–40660900–11001235
40–100560800–9501440
Sources and technical details

Thickness equivalents: ≤ 8, 8–20 and 20–60 mm. Charpy (ISO-V) at least 30–35 J. Ovako gives the same values for the 16–40 and 40–100 mm ranges.

Saarstahl — 41Cr4 / 41CrS4 data sheet — Werkstoff-Datenblatt, p.1; EN 10083 quenched-and-tempered steel.

Ovako Steel Navigator — 41Cr4 — Composition, mechanical property and heat-treatment tables.

Heat treatment and delivery hardness

Bar is usually supplied soft annealed (+A) or treated for shearability (+S) and quenched and tempered after machining. The temperatures below are processing temperatures, not service temperatures.

Treatment or conditionValueNote
Hardening820–860°COil or water
Tempering540–680°CTo the required strength
Soft annealing680–720°CSlow furnace cooling
Soft annealed (+A)Max 241 HBSaarstahl and Ovako
Treated for shearability (+S)Max 255 HBSaarstahl
Sources and technical details

Saarstahl — 41Cr4 / 41CrS4 data sheet — Werkstoff-Datenblatt, p.1; EN 10083 quenched-and-tempered steel.

Ovako Steel Navigator — 41Cr4 — Composition, mechanical property and heat-treatment tables.

41Cr4 equivalents: 5140, SCr440, 530M40

41Cr4 has the material number 1.7035; its resulphurised free-machining version is 41CrS4 (1.7039). Saarstahl lists SAE 5140, BS 530M40 and AFNOR 42C4 as counterparts; the Japanese counterpart is SCr440. These are close, not identical: SAE 5140 has 0.70–0.90 chromium, 41Cr4 0.90–1.20.

Typical application areas

Crankshafts, axles, steering knuckles, steering parts, shafts.

Product and cutting options

Relevant product forms for this material are listed below. Availability varies with grade and dimensions.