PRECISION IN MATERIAL. CLARITY IN SUPPLY.

SHEET METAL

Press brake tonnage calculator: bending force and V die

Enter the sheet thickness, bend length and V die opening and choose the material to see the air-bending force in kN and tonnes, the tonnage per metre and the recommended die opening.

Sheet and die

Material

For air bending. The presets are approximate; enter the Rm from the material certificate. Bottoming and coining need much more force.

F = 1,42 × Rm × t² × L / (V × 1000)

Bending force

24.4 t239.6 kN
Per metre
24.4 t/m
V / t ratio
8
Bending force: 239.6 kN (24.4 t), 24.4 t/m · t 3 mm, L 1000 mm, V 24 mm, Rm 450 MPa

Press brake tonnage chart (metric)

Air-bending force per metre of bend at the typical V = 8 × t, from the formula on this page (mild steel 450 MPa, stainless 650 MPa).

Tonnes per metre by sheet thicknessV (mm) · Mild steel (t/m) · Stainless (t/m)
t (mm)V (mm)Mild steel (t/m)Stainless (t/m)
188.111.8
1.51212.217.6
21616.323.5
2.52020.429.4
32424.435.3
43232.647.1
54040.758.8
64848.970.6
86465.294.1
108081.4117.6
129697.7141.2

Press brake tonnage formula

The force needed for air bending is estimated as F (kN) = 1.42 × Rm × t² × L / (V × 1000), with Rm the tensile strength (MPa), t the sheet thickness, L the bend length and V the die opening (mm). Divide kN by 9.807 for tonnes. Press brake makers’ “P = 650 × t² × L / V” (L in metres) is the same calculation simplified for 450 MPa mild steel.

Example: 3 mm mild steel, 1 m bend, 24 mm V die: F = 1.42 × 450 × 9 × 1000 / (24 × 1000) ≈ 239.6 kN, about 24.4 tonnes.

How to choose the V die opening

For air bending the V die opening is usually 6–10 times the sheet thickness, most often 8 times: 18–30 mm, typically 24 mm, for 3 mm sheet. Force is inversely proportional to V: bending the same sheet in a 16 mm die needs 359.4 kN. A narrow die raises the force and tightens the inside radius; a wide die lowers the force but enlarges the inside radius and the shortest flange.

Bending force by material

Force is proportional to tensile strength. Stainless needs about 1.4–1.5 times the force of mild steel at the same thickness: 3 mm stainless in a 24 mm die is about 346.1 kN. For aluminium it varies widely with alloy and temper. Enter the Rm from the material certificate; if unknown, use the upper limit of the standard.

Air bending, bottoming and coining

The calculator is for air bending, where the sheet is formed by the punch depth without touching the bottom of the die. Bottoming needs several times more force and coining much more; use the press brake maker’s chart for those. Leave a margin above the calculated tonnage rather than running the machine at its limit, and spread the force along the machine length.

Frequently asked questions

How is press brake tonnage calculated?

F (kN) = 1.42 × Rm × t² × L / (V × 1000): multiply tensile strength (MPa) by thickness squared and bend length (mm), divide by the die opening (mm) and 1000; divide by 9.807 for tonnes.

How many tonnes to bend 2 mm sheet?

For mild steel in a 16 mm V die, about 16.3 tonnes per metre. Stainless needs about 1.4–1.5 times as much.

How do I choose a press brake die?

Choose a V opening of 6–10 times the sheet thickness, most often 8 times. A wider die lowers the force for thick or stainless sheet; a narrower die gives a smaller inside radius but needs more tonnage.

How much force does stainless sheet need?

About 1.4–1.5 times that of mild steel with the same thickness and die. The calculator has a 650 MPa preset for stainless; the certificate Rm gives a more accurate result.

What does tonnes per metre mean?

Press brake charts give the force for a 1 m bend. Force is proportional to bend length, so a 500 mm bend needs half and a 2 m bend twice as much.